Dover markem imaje CSAT ITS6 210 Скачать руководство пользователя страница 105 | Manualshive

Страница: 105 / 370

background image

Operating Instructions

Machine Description

© Copyright by Markem-Imaje CSAT GmbH

ITS6_135_Manual_EN.doc

Subject to Technical Modifications

Page 105 / 370

Pos. Element

Bedeutung

1

Sensor

Whenever the permissible material thickness is
exceeded, the sensor will trigger the abrupt stop
of the machine.

2

Scanning bar

Floats normally above the printing material. Is
touched and raised by too thick a printing materi-
al.

3

Marks

Marks for adjusting the scanning bar to the thick-
ness of the employed printing material.

Function of the infeed height control

The infeed height control monitors the height of the material.

If a label comes loose from the substrate and sticks up, or two labels are
stuck on top of each other, they should not be allowed to enter the printing
unit.

Whenever the permissible material thickness is exceeded, the sensor will
trigger the abrupt stop of the machine and its feed process, so that the la-
bels in question cannot enter the printing unit.

Functional principle: The scanning bar of the height control floats above the
entire printing width of the printing substrate

. Whenever “thicker” material

comes along, then the scanning bar will rise, which in turn lifts a lever from
a corresponding sensor inside the printer. If the distance is too great, the
sensor will trigger an alarm and cause the transport of material to be
stopped abruptly.

The scanning bar sits on an eccentric and can be rotated. This permits the
scanning bar to be adjusted to different printing material thicknesses. Mark
#3 shows the currently selected value. Adjust the required value when you
change the printing material.

The range specification defines the thickness of the printing material in mil-
limeters. The specification in parentheses defines the maximum passage
height in millimeters.

Example: "0.0 - 0.2 (0.5)" means: This setting is suitable for printing materi-
al of a thickness of 0.0 ... 0.2 mm. Any irregularities may pass infeed height
control up to a height of 0.5 mm.

Notice

Solely the system user is responsible for any damage on the print
heads that results from incorrect settings of the infeed height control
unit!

Use the specifications in the following table when you select the deflection
rollers for a printing material and when you adjust the scanning bar of the
infeed height control unit.

«
...
103
104
105
106
107
...
»

Содержание markem imaje CSAT ITS6 210



















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для markem imaje CSAT ITS6 210

Бренд: WaxJet Страницы: 131

Бренд: IBM Страницы: 16

Бренд: Panasonic Страницы: 32

Бренд: Olympus Страницы: 2

Delta Rostock mini G2 pro

Бренд: Geeetech Страницы: 89

Бренд: KIP Страницы: 103

Бренд: BIO RAD Страницы: 61

Бренд: iFactory3D Страницы: 14

Бренд: DAKEWE Страницы: 94

Бренд: idp Страницы: 48

Бренд: Oki Страницы: 188

Бренд: Oce Страницы: 32

Бренд: TonerRefillKits Страницы: 10

DocuColor 45087638

Бренд: Xerox Страницы: 28

Бренд: SPRT Страницы: 18

Бренд: MIMAKI Страницы: 30

Бренд: Black Box Страницы: 30

C11C418001 - Stylus C60 Inkjet Printer

Бренд: Epson Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды