Dover markem imaje CSAT ITS6 210 Скачать руководство пользователя страница 121 | Manualshive

Страница: 121 / 370

background image

Operating Instructions

Machine Description

© Copyright by Markem-Imaje CSAT GmbH

ITS6_135_Manual_EN.doc

Subject to Technical Modifications

Page 121 / 370

4.6.17.3 Care of the pre-curing unit

In general, the cleanliness of the LED strips of the pre-curing unit only has
to be checked once a day when the print heads are cleaned by hand. If for-
eign objects or ink film and drops are visible on an LED strip, they should
be removed using only a soft, lint-free cloth if possible (see Chap.10.7.5.2,
"Manual cleaning of the print heads").

Notice



Clean the LED strips and the surrounding areas using only dry,

soft cloths (Order no.:

FF100252100

).



Dried-on or cross-linked ink spots should be removed using only

the special cleaning pads no.

ZE1010-75

.



All other cleansers are prohibited.

Notice



Never clean the LED strips and the adjacent areas with aggressive

solvents (e.g. acetone) or wipe off with dripping wet low-viscosity
liquids (e.g. water, glass cleaner, isopropyl alcohol)!



Solvents and low-viscosity cleansers are prohibited since they can

penetrate the lamp module and cause damage there.



Never scratch or scrape the glass shields using hard objects!

Notice

Risk whenever the printing substrate should tear:



If the printing substrate should tear between the area of the cut-

and-splice device on the unwinding unit side and the friction drive,
then all of the print heads and the LED strips of the pre-curing unit
should be checked immediately and cleared of any foreign objects
or spots of ink.

«
...
119
120
121
122
123
...
»

Содержание markem imaje CSAT ITS6 210



















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для markem imaje CSAT ITS6 210

Бренд: Xerox Страницы: 108

WorkCentre 4265

Бренд: Xerox Страницы: 20

Бренд: Xerox Страницы: 11

WORKCENTRE 5050

Бренд: Xerox Страницы: 186

7500DX - Phaser Color LED Printer

Бренд: Xerox Страницы: 5

Бренд: Canon Страницы: 2

imageRUNNER C3480

Бренд: Canon Страницы: 92

Бренд: Oki Страницы: 328

Бренд: DNP Страницы: 2

Бренд: Oce Страницы: 209

Бренд: Labelmate Страницы: 61

Бренд: Posnet Страницы: 2

Бренд: idp Страницы: 48

Бренд: SATO Страницы: 255

Бренд: Xprinter Страницы: 40

Бренд: Canon Страницы: 22

Бренд: Canon Страницы: 4

Бренд: Canon Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды