manualshive.com logo in svg

Digi NS9215, Справочник по аппаратуре, Страница: 271 / 517

Поделиться
Скачать
Digi NS9215 Скачать руководство пользователя страница 271

. . . . .

E T H E R N E T   C O M M U N I C A T I O N   M O D U L E

Transmit packet processor

www.digiembedded.com

271

Transmitting a 
frame

Setting the EXTDMA (enable transmit DMA) bit in Ethernet General Control Register 
#1 starts the transfer of transmit frames from the system memory to the TX_FIFO. 
The 

TX_WR

 logic reads the first buffer descriptor in the TX buffer descriptor RAM. 

If the F bit is set, it transfers data from system memory to the TX_FIFO using 
the buffer pointer as the starting point. This process continues until the end of 
the buffer is reached. The address for each subsequent read of the buffer is 
incremented by 32 bytes (that is, 

0x20

). The buffer length field in the buffer 

descriptor is decremented by this same value, each transfer, to identify when 
the end of the buffer is reached.

If the L field in the buffer descriptor is 0, the next buffer descriptor in the RAM 
continues the frame transfer until the L field in the current buffer descriptor is 
1. This identifies the current buffer as the last buffer of a transmit frame.

After the entire frame has been written to the TX_FIFO, the 

TX_WR

 logic waits for a 

signal from the 

TX_RD

 logic indicating that frame transmission has completed at the 

MAC. The 

TX_WR

 logic updates the buffer length, status, and F fields of the current 

buffer descriptor (that is, the last buffer descriptor for the frame) in the TX buffer 
descriptor RAM when the signal is received.

F

When set, indicates the buffer is full. The 

TX_WR

 logic clears this bit after emptying 

a buffer. The system software sets this bit as required, to signal that the buffer is ready 
for transmission. If the 

TX_WR

 logic detects that this bit is not set when the buffer 

descriptor is read, it does one of two things:

 

If a frame is not in progress, the 

TX_WR

 logic sets the 

TXIDLE

 bit in the Ethernet 

Interrupt Status register.

 

If a frame is in progress, the 

TXBUFNR

 bit in the Ethernet Interrupt Status 

register is set.

In either case, the 

TX_WR

 logic stops processing frames until 

TCLER

 (clear transmit 

logic) in Ethernet General Control Register #2 is toggled from low to high.

TXBUFNR

 is set only for frames that consist of multiple buffer descriptors and 

contain a descriptor — 

not

 the first descriptor — that does not have the F bit set after 

frame transmission has begun.

Buffer length

This is a dual use field:

 

When the buffer descriptor is read from the TX buffer descriptor RAM, buffer 

length indicates the length of the buffer, in bytes. The 

TX_WR

 logic uses this 

information to identify the end of the buffer. For proper operation of the 

TX_WR

 

logic, all transmit frames must be at least 34 bytes in length.

 

When the 

TX_WR

 logic updates the buffer descriptor at the end of the frame, it 

writes the length of the frame, in bytes, into this field for the last buffer 
descriptor of the frame. 
If the MAC is configured to add the CRC to the frame (that is, CRCEN in MAC 
Configuration Register #2 is set to 1), this field will include the four bytes of 
CRC. This field is set to 0x000 for jumbo frames that are aborted. Only the 
lower 11 bits of this field are valid, since the maximum legal frame size for 
Ethernet is 1522 bytes.

Field

Description

Содержание NS9215






































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов