Daikin EBLA04E V Series Скачать руководство пользователя страница 72

Страница: 72 / 324

Troubleshooting

Service manual

EBLA04~08E + EDLA04~08E

Daikin Altherma 3 M
ESIE22-09 – 2022.05

DANGER: RISK OF ELECTROCUTION

Confirm the rectifier voltage is below 10 V DC before proceeding, see

Check that the thermal interface grease is applied properly on the (PCB or
refrigerant piping) contact surface of the heat sink. Adjust if needed.

Possible cause:

Thermal interface grease NOT applied properly on the heat

sink.

INFORMATION

If all procedures listed above have been performed and the problem is still present,
contact the helpdesk.

3.3.79 U5-00 – User interface communication problem

Trigger

Effect

Reset

Communication failure
between unit and user
interface.

Unit will stop operating.

Automatic reset.

To solve the error code

INFORMATION

It is recommended to perform the checks in the listed order.

Perform a check of the hydro PCB. See

"4.12 Hydro PCB"

[

175].

Possible cause:

Faulty hydro PCB.

Check if the remote controller user interface functions correctly. See

"4.20 User interface"

[

234].

Possible cause:

Faulty remote controller user interface.

Check the communication wiring between the remote controller and the unit.
See

"4.20 User interface"

[

234].

Possible cause:

Faulty wiring between the remote controller and the unit.

Check if the power supply is compliant with the regulations. See

Possible cause:

▪

Faulty or disturbance of the power supply (power supply MUST be within
range of nominal operating voltage ±4%),

▪

Power drop,

▪

Short circuit.

INFORMATION

If all procedures listed above have been performed and the problem is still present,
contact the helpdesk.

draft – 31/05/2022 15:53

Содержание EBLA04E V Series




































































































































































































































































































































Результаты поиска

Содержание EBLA04E V Series

Отзывы:

Daikin EBLA04E V Series, Руководство по обслуживанию, Страница: 72 / 324

Результаты поиска

Содержание EBLA04E V Series

Отзывы: