Daikin EBLA04E V Series Скачать руководство пользователя страница 129

Страница: 129 / 324

Components

Service manual

129

EBLA04~08E + EDLA04~08E
Daikin Altherma 3 M
ESIE22-09 – 2022.05

For backup heater option with 1~, 230 V, 3 kW or 6 kW backup heater:

▪

K1M: 2‑6 / 1‑5, 4‑6 / 3‑5

▪

K5M: 2‑6 / 1‑5, 4‑6 / 3‑5, 2‑14 / 1‑13
All measured voltages MUST be 230 V AC ± 10% (contact closed).

For backup heater option with 3~, 400 V, 6 kW or 9 kW backup heater:

▪

K1M: 2‑4 / 1‑3, 4‑6 / 3‑5, 2‑6 / 1‑5

▪

K5M: 2‑4 / 1‑3, 4‑6 / 3‑5, 2‑6 / 1‑5
All measured voltages MUST be 400 V AC ± 10% (contact closed).

▪

K5M: 2‑14 / 1‑13
The measured voltage MUST be 230 V AC ± 10% (contact closed).

Activate backup heater: step 2.

Measure the voltage between the following terminals of the backup heater
contactors.

For backup heater option with 1~, 230 V, 3 kW or 6 kW backup heater:

▪

K2M: 2‑6 / 1‑5, 4‑6 / 3‑5

▪

K5M: 2‑6 / 1‑5, 4‑6 / 3‑5, 2‑14 / 1‑13

▪

K2M: 1‑K5M: 14
All measured voltages MUST be 230 V AC ± 10% (contact closed).

For backup heater option with 3~, 400 V, 6 kW or 9 kW backup heater:

▪

K2M: 2‑4 / 1‑3, 4‑6 / 3‑5, 2‑6 / 1‑5

▪

K5M: 2‑4 / 1‑3, 4‑6 / 3‑5, 2‑6 / 1‑5
All measured voltages MUST be 400 V AC ± 10% (contact closed).

▪

K5M: 2‑14 / 1‑13
The measured voltage MUST be 230 V AC ± 10% (contact closed).

INFORMATION

Make sure that the wiring between the backup heater contactors is properly
connected and NOT damaged (check continuity), see

"7.2 Wiring diagram"

[

281].

Are the measured voltages of the
backup heater contactors correct
(contacts closed)?

Action

Yes

Continue with the next step.

Skip the next steps and continue with
the operating voltage check of the
specific contactor.

Deactivate backup heater: Step 2 and backup heater: Step 1.

Measure the voltage between the following terminals of the backup heater
contactors.

For backup heater option with 1~, 230 V, 3 kW or 6 kW backup heater:

▪

K1M: 1‑5, 3‑5

▪

K2M: 1‑5, 3‑5

▪

K5M: 1‑5, 3‑5, 1‑13
All measured voltages MUST be 0 V AC (contacts open).

For backup heater option with 3~, 400 V, 6 kW or 9 kW backup heater:

▪

K1M: 1‑3, 3‑5, 1‑5

▪

K2M: 1‑3, 3‑5, 1‑5

▪

K5M: 1‑3, 3‑5, 1‑5, 1‑13
All measured voltages MUST be 0 V AC (contacts open).

draft – 31/05/2022 15:53

Содержание EBLA04E V Series




































































































































































































































































































































Результаты поиска

Содержание EBLA04E V Series

Отзывы:

Daikin EBLA04E V Series, Руководство по обслуживанию, Страница: 129 / 324

Результаты поиска

Содержание EBLA04E V Series

Отзывы: