Daikin EBLA04E V Series Скачать руководство пользователя страница 100

Страница: 100 / 324

Components

Service manual

100

EBLA04~08E + EDLA04~08E

Daikin Altherma 3 M
ESIE22-09 – 2022.05

Are the measured voltages correct?

Action

Yes

Perform a position check of the 3‑way
valve (automatic procedure), see

"4.1.1 Checking procedures"

[

99].

Continue with the next step.

Measure the voltage on connector X17A pin 5 and 7.

Result:

The measured voltage MUST be 230 V AC.

Is the measured voltage on connector
X17A correct?

Action

Yes

Continue with the next step.

Perform a check of the hydro PCB, see

"4.12.1 Checking procedures"

[

175].

Disconnect connector X20A from the hydro PCB.

Activate

DHW operation

via the user interface.

Measure the resistance between X20A pin 3 and 5.

Result:

The measured resistance MUST be 0 Ω.

De-activate

DHW operation

and activate

Space operation

via the user

interface.

Measure the resistance between X20A pin 1 and 5.

Result:

The measured resistance MUST be 0 Ω.

Is the resistance for both
measurements on connector X20A
correct?

Action

Yes

Relay KVR is switching correctly. Correct
the wiring between X20A, X17A and
X2M, see

"7.2 Wiring Diagram"

[

281].

Relay KVR is NOT switching correctly.
Replace the hydro PCB, see

"4.12.2 Repair procedures"

[

178],

To perform a position check of the 3-way valve (automatic procedure)

Prerequisite:

First perform an electrical check of the 3‑way valve, see

"4.1.1 Checking procedures"

[

99].

Turn ON the power of the unit.

Activate

DHW operation

via the user interface.

Use a contact thermometer to measure the temperature at the 3‑way valve
water inlet, the domestic hot water exit and the space heating exit.

Exit

Temperature

Domestic hot water

Same as the 3-way valve inlet

Space heating

"Much" lower than the 3-way valve inlet

The 3-way valve can be installed in accordance with one of the following four
configurations. Water inlet and exit locations differ depending on the
configuration used in your unit.

draft – 31/05/2022 15:53

Содержание EBLA04E V Series




































































































































































































































































































































Результаты поиска

Содержание EBLA04E V Series

Отзывы:

Daikin EBLA04E V Series, Руководство по обслуживанию, Страница: 100 / 324

Результаты поиска

Содержание EBLA04E V Series

Отзывы: