Daikin EBLA04E V Series Скачать руководство пользователя страница 143

Страница: 143 / 324

Components

Service manual

143

EBLA04~08E + EDLA04~08E
Daikin Altherma 3 M
ESIE22-09 – 2022.05

To perform an insulation check of the booster heater

Prerequisite:

First perform a resistance check of the booster heater, see

"4.5.1 Checking procedures"

[

142].

Open all circuit breakers.

CAUTION

To prevent damage to the unit, all circuit breakers MUST be opened before using a
Megger.

Set the Megger voltage to 500 V AC.

Connect the Megger ground test lead directly to the booster heater ground
wire.

CAUTION

Do NOT connect the Megger ground test lead to any other ground wire.

Measure the insulation resistance between the following terminals. The
measured insulation resistance MUST be >3 MΩ.

Terminals

K3M1‑ground

K3M3‑ground

Is the measured booster heater
insulation resistance correct?

Action

Yes

Return to

"4.5.1 Checking

procedures"

[

142] of the booster

heater and continue with the next
procedure.

Replace the booster heater, see

"4.5.2 Repair procedures"

[

146].

To perform an electrical check of the booster heater

Prerequisite:

First perform an insulation check of the booster heater, see

"4.5.1 Checking procedures"

[

142].

Prerequisite:

Check the circuit breaker. Reset if it has tripped.

Turn ON the power of the unit.

INFORMATION

If the circuit breaker or the booster heater thermal protector trips again, determine
the root cause of the problem. Something is overloading the electrical circuit or
creating a short-circuit.

Activate

Installer

on the user interface. See the installer reference guide

for the correct procedure.

Go to

Actuator test run

via the user interface.

Activate Booster heater test.

Check the status in the Actuators menu of the user interface. This MUST be:

▪

Booster heater test = ON

Check if the field installed circuit breaker has tripped.

draft – 31/05/2022 15:53

Содержание EBLA04E V Series




































































































































































































































































































































Результаты поиска

Содержание EBLA04E V Series

Отзывы:

Daikin EBLA04E V Series, Руководство по обслуживанию, Страница: 143 / 324

Результаты поиска

Содержание EBLA04E V Series

Отзывы: