Daikin EBLA04E V Series Скачать руководство пользователя страница 99 | Manualshive

Страница: 99 / 324

Daikin EBLA04E V Series Скачать руководство пользователя страница 99

4

|

Components

Service manual

99

EBLA04~08E + EDLA04~08E
Daikin Altherma 3 M
ESIE22-09 – 2022.05

4 Components

CAUTION

When replacing a component ALWAYS make sure the correct spare part for your unit
is installed.

4.1 3-way valve

4.1.1 Checking procedures

INFORMATION

It is recommended to perform the checks in the listed order.

To perform a mechanical check of the 3-way valve

Prerequisite:

Stop the unit operation via the user interface.

Prerequisite:

Turn OFF the respective circuit breaker.

Prerequisite:

Remove the required plate work, see

"4.16 Plate work"

1

The 3‑way valve knob MUST be fully pressed (= motor control). If NOT fully
pressed, press the 3‑way valve knob.

2

The 3‑way valve knob MUST be in domestic hot water or space heating
position, NOT in intermediate position. If in intermediate position, put the
3‑way valve switch in domestic hot water or space heating position.

Is the problem solved?

Action

Yes

No further actions required.

No

Perform an electrical check of the 3-way
valve, see

"4.1.1 Checking

To perform an electrical check of the 3-way valve

Prerequisite:

First perform a mechanical check of the 3-way valve, see

"4.1.1 Checking procedures"

1

Turn ON the power of the unit.

2

Activate

DHW operation

via the user interface.

3

Measure the voltage on connector X2M pin 13 and pin 14a.

Result:

The measured voltage MUST be 230 V AC.

4

Measure the voltage on connector X2M pin 13 and pin 12.

Result:

The measured voltage MUST be 230 V AC.

5

De-activate

DHW operation

and activate

Space operation

via the user

interface.

6

Measure the voltage on connector X2M pin 13 and pin 14a.

Result:

The measured voltage MUST be 230 V AC.

7

Measure the voltage on connector X2M pin 13 and pin 12.

Result:

The measured voltage MUST be 0 V AC.

draft – 31/05/2022 15:53

«
...
97
98
99
100
101
...
»

Содержание EBLA04E V Series





































































































































































































































































































































Отзывы:

Нет отзывов