Daikin EBLA04E V Series Скачать руководство пользователя страница 41

Страница: 41 / 324

Troubleshooting

Service manual

EBLA04~08E + EDLA04~08E
Daikin Altherma 3 M
ESIE22-09 – 2022.05

Check if the power supply is compliant with the regulations. See

Possible cause:

▪

Faulty or disturbance of the power supply (power supply MUST be within
range of nominal operating voltage ±4%),

▪

Power drop,

▪

Short circuit.

Perform a check of the outdoor unit fan motor. See

"4.15 Outdoor unit fan

motor"

[

197].

Possible cause:

Faulty outdoor unit fan motor.

Perform a check of the compressor. See

"4.7 Compressor"

[

148].

Possible cause:

Faulty compressor or miswiring of the compressor power

supply cable.

Prerequisite:

Stop the unit operation via the user interface.

Prerequisite:

Turn OFF the respective circuit breaker.

Wait until the rectifier voltage is below 10 V DC.

DANGER: RISK OF ELECTROCUTION

Confirm the rectifier voltage is below 10 V DC before proceeding, see

Check that the thermal interface grease is applied properly on the (PCB or
refrigerant piping) contact surface of the heat sink. Adjust if needed.

Possible cause:

Thermal interface grease NOT applied properly on the heat

sink.

INFORMATION

If all procedures listed above have been performed and the problem is still present,
contact the helpdesk.

3.3.34 E2-00 – Leakage current detection error

Trigger

Effect

Reset

An earth leak was
detected by the outdoor
main/inverter PCB.

Unit will stop operating.

Power supply reset.

To solve the error code

INFORMATION

It is recommended to perform the checks in the listed order.

Perform an electrical check and insulation check of the compressor. See

"4.7 Compressor"

[

148].

Possible cause:

Faulty compressor or miswiring of the compressor power

supply cable.

Perform a check of the main PCB. See

"4.14 Main PCB"

[

184].

Possible cause:

Faulty main PCB.

draft – 31/05/2022 15:53

Содержание EBLA04E V Series




































































































































































































































































































































Результаты поиска

Содержание EBLA04E V Series

Отзывы:

Daikin EBLA04E V Series, Руководство по обслуживанию, Страница: 41 / 324

Результаты поиска

Содержание EBLA04E V Series

Отзывы: