Daikin EBLA04E V Series Скачать руководство пользователя страница 135

Страница: 135 / 324

Components

Service manual

135

EBLA04~08E + EDLA04~08E
Daikin Altherma 3 M
ESIE22-09 – 2022.05

If the backup heater thermal protector has tripped:

▪

Sufficiently cool the backup heater thermal protector (7 K)

▪

Press the button on the top to reset the backup heater thermal protector

Reset button

Screw

Backup heater thermal protector

Backup heater

Loosen and remove the 2 screws and remove the backup heater thermal
protector from the backup heater.

Using a hot air gun, heat the backup heater thermal protector above 88°C.

Result:

The backup heater thermal protector MUST trip at a temperature of

82~88°C.

DANGER: RISK OF BURNING/SCALDING

Does the backup heater thermal
protector trip at correct temperature?

Action

Yes

Perform an electrical check of the
backup heater thermal protector, see

"Checking procedures"

[

134]

Replace the backup heater thermal
protector, see

To perform an electrical check of the backup heater thermal protector

Prerequisite:

First perform a mechanical check of the backup heater thermal

protector, see

"Checking procedures"

[

134].

Prerequisite:

Stop the unit operation via the user interface.

Prerequisite:

Turn OFF the respective circuit breaker.

With the backup heater thermal protector NOT activated (temperature below
82°C), measure the resistance between the backup heater thermal protector
wires on terminal X7M: 5‑6.

Result:

The resistance MUST be 0 Ω (backup heater thermal protector

contacts are closed).

draft – 31/05/2022 15:53

Содержание EBLA04E V Series




































































































































































































































































































































Результаты поиска

Содержание EBLA04E V Series

Отзывы:

Daikin EBLA04E V Series, Руководство по обслуживанию, Страница: 135 / 324

Результаты поиска

Содержание EBLA04E V Series

Отзывы: