Daikin EBLA04E V Series Скачать руководство пользователя страница 26

Страница: 26 / 324

Troubleshooting

Service manual

EBLA04~08E + EDLA04~08E

Daikin Altherma 3 M
ESIE22-09 – 2022.05

Perform a check of the inlet water thermistor. See

"4.19 Thermistors"

[

217].

Possible cause:

Faulty inlet water thermistor.

Perform a check of the outlet water after heat exchanger thermistor. See

"4.19 Thermistors"

[

217].

Possible cause:

Faulty outlet water after heat exchanger thermistor.

Perform

check

the

refrigerant

liquid

thermistor.

See

"4.19 Thermistors"

[

217].

Possible cause:

Faulty refrigerant liquid thermistor.

Perform a check of the hydro PCB. See

"4.12 Hydro PCB"

[

175].

Possible cause:

Faulty hydro PCB.

Check that all stop valves of the refrigerant circuit are open. See

"5.2 Refrigerant circuit"

[

256].

Possible cause:

Closed stop valve in the refrigerant circuit.

Check if the refrigerant circuit is correctly charged. See

Possible cause:

Refrigerant overcharge.

Check if the refrigerant circuit is clogged. See

"5.2 Refrigerant circuit"

[

256].

Possible cause:

Clogged refrigerant circuit.

Check for the presence of non‑condensables and/or humidity in the
refrigerant circuit. See

"5.2 Refrigerant circuit"

[

256].

Possible cause:

Non‑condensables and/or humidity in the refrigerant circuit.

Check the water flow. See

"5.3 Water circuit"

[

265].

Possible cause:

Water flow is too low.

Check the water pressure. See

"5.3 Water circuit"

[

265].

Possible cause:

Water pressure is too low.

INFORMATION

If all procedures listed above have been performed and the problem is still present,
contact the helpdesk.

3.3.12 89-02 – Heat exchanger frozen

Trigger

Effect

Reset

Condensing temperature
<0°C during space
heating.

Unit will stop operating.

Automatic reset.

Liquid refrigerant
thermistor ≤0°C during
space heating or domestic
hot water.

To solve the error code

INFORMATION

It is recommended to perform the checks in the listed order.

draft – 31/05/2022 15:53

Содержание EBLA04E V Series




































































































































































































































































































































Результаты поиска

Содержание EBLA04E V Series

Отзывы:

Daikin EBLA04E V Series, Руководство по обслуживанию, Страница: 26 / 324

Результаты поиска

Содержание EBLA04E V Series

Отзывы: