manualshive.com logo in svg

Daikin EBLA04E V Series, Руководство по обслуживанию, Страница: 53 / 324

Поделиться
Скачать
Daikin EBLA04E V Series Скачать руководство пользователя страница 53

3

 | 

Troubleshooting

Service manual

53

EBLA04~08E + EDLA04~08E
Daikin Altherma 3 M
ESIE22-09 – 2022.05

To solve the error code

INFORMATION

It is recommended to perform the checks in the listed order.

1

Clean the outdoor heat exchanger. See 

"6 Maintenance"

 [

4

 275].

Possible cause: 

Dirty outdoor heat exchanger.

2

Check  that  all  stop  valves  of  the  refrigerant  circuit  are  open.  See

"5.2 Refrigerant circuit"

 [

4

 256].

Possible cause: 

Closed stop valve in the refrigerant circuit.

3

Check the outdoor temperature. See 

"5.5 External factors"

 [

4

 274].

Possible cause: 

Outdoor temperature is out of operation range.

4

Check  the  required  space  around  the  outdoor  unit  heat  exchanger.  See

"5.5 External factors"

 [

4

 274].

Possible  cause: 

Insufficient  air  flow  or  air  by‑pass  due  to  required  space

specifications not met.

5

Perform 

a 

check 

of 

the 

heat 

exchanger 

thermistor. 

See

"4.19 Thermistors"

 [

4

 217].

Possible cause: 

Faulty heat exchanger thermistor.

6

Perform a check of the expansion valve. See 

"4.9 Expansion valve"

 [

4

 162].

Possible cause: 

Faulty expansion valve.

7

Perform a check of the main PCB. See 

"4.14 Main PCB"

 [

4

 184].

Possible cause: 

Faulty main PCB.

8

Check  if  the  refrigerant  circuit  is  correctly  charged.  See 

"5.2  Refrigerant

circuit"

 [

4

 256].

Possible cause: 

Refrigerant overcharge.

9

Check  for  the  presence  of  non‑condensables  and/or  humidity  in  the
refrigerant circuit. See 

"5.2 Refrigerant circuit"

 [

4

 256].

Possible cause: 

Non‑condensables and/or humidity in the refrigerant circuit.

10

Check if the refrigerant circuit is clogged. See 

"5.2 Refrigerant circuit"

 [

4

 256].

Possible cause: 

Clogged refrigerant circuit.

11

Perform  a  check  of  the  outdoor  unit  fan  motor.  See 

"4.15  Outdoor  unit  fan

motor"

 [

4

 197].

Possible cause: 

Faulty outdoor unit fan motor.

INFORMATION

If all procedures listed above have been performed and the problem is still present,
contact the helpdesk.

3.3.49 H0-00 – Outdoor unit: Voltage/current sensor problem

Trigger

Effect

Reset

Compressor voltage (DC)
is out of range before
start‑up.

Unit will stop operating.

Manual reset via user
interface.

draft – 31/05/2022 15:53

Содержание EBLA04E V Series





































































































































































































































































































































Отзывы:

Нет отзывов