manualshive.com logo in svg

Daikin EBLA04E V Series, Руководство по обслуживанию, Страница: 28 / 324

Поделиться
Скачать
Daikin EBLA04E V Series Скачать руководство пользователя страница 28

3

 | 

Troubleshooting

Service manual

28

EBLA04~08E + EDLA04~08E

Daikin Altherma 3 M
ESIE22-09 – 2022.05

To solve the error code

INFORMATION

It is recommended to perform the checks in the listed order.

1

Check the water flow. See 

"5.3 Water circuit"

 [

4

 265].

Possible cause: 

Water flow is too low.

2

Check  the  minimum  required  water  volume  for  your  unit.  See  installer
reference guide.

Possible cause: 

Water volume is too low.

3

Perform  a  check  of  the  refrigerant  pressure  sensor.  See 

"4.18  Refrigerant

pressure sensor"

 [

4

 212].

Possible cause: 

Faulty refrigerant pressure sensor.

4

Perform  a  check  of  the  outlet  water  after  heat  exchanger  thermistor.  See

"4.19 Thermistors"

 [

4

 217].

Possible cause: 

Faulty outlet water after heat exchanger thermistor.

5

Check  if  the  refrigerant  circuit  is  correctly  charged.  See 

"5.2  Refrigerant

circuit"

 [

4

 256].

Possible cause: 

Refrigerant overcharge or shortage.

6

Check if the refrigerant circuit is clogged. See 

"5.2 Refrigerant circuit"

 [

4

 256].

Possible cause: 

Clogged refrigerant circuit.

7

Check  for  the  presence  of  non‑condensables  and/or  humidity  in  the
refrigerant circuit. See 

"5.2 Refrigerant circuit"

 [

4

 256].

Possible cause: 

Non‑condensables and/or humidity in the refrigerant circuit.

8

Perform a check of the hydro PCB. See 

"4.12 Hydro PCB"

 [

4

 175].

Possible cause: 

Faulty hydro PCB.

INFORMATION

If all procedures listed above have been performed and the problem is still present,
contact the helpdesk.

3.3.15 89-06 – Heat exchanger freeze-up protection activated during cooling (warning)

Trigger

Effect

Reset

Water heat exchange
freezing abnormality
during cooling.
Outlet water temperature
<5°C or 1.5°C (glycol) for
5 seconds OR saturated
evaporation temperature
(pressure sensor) <−11°C
for 5 minutes from start
of cooling.
At second occurrence,
error 89‑05 is triggered.

Unit will stop operating.

Auto reset.

draft – 31/05/2022 15:53

Содержание EBLA04E V Series





































































































































































































































































































































Отзывы:

Нет отзывов