manualshive.com logo in svg

Daikin EBLA04E V Series, Руководство по обслуживанию, Страница: 182 / 324

Поделиться
Скачать
Daikin EBLA04E V Series Скачать руководство пользователя страница 182

4

 | 

Components

Service manual

182

EBLA04~08E + EDLA04~08E

Daikin Altherma 3 M
ESIE22-09 – 2022.05

LED

Description

Behaviour

LD2

Indication of TCP/IP
communication with the
router.

▪

LED 

ON: 

normal

communication.

▪

LED  flashing:  communication
problem. 

Check 

TCP/IP

communication 

with 

the

router.

LD3

Indication of communication
with the indoor unit.

▪

LED 

ON: 

normal

communication.

▪

LED  flashing:  communication
problem. 

Check 

the

communication  between  the
LAN  adapter  and  the  unit
PCB, 

"4.13.1 

Checking

procedures"

 [

4

 181].

LD4

(a)

Indication of Smart Grid
activity.

▪

LED  ON:  system  running  in
the  "Recommended  ON",
"Forced ON", or "Forced OFF"
Smart Grid operation mode.

▪

LED  OFF:  system  running  in
the 

"Normal 

operation"

Smart  Grid  operation  mode,
or 

operating 

in 

normal

operation  conditions  (space
heating/cooling,  production
of domestic hot water).

▪

LED  flashing:  LAN  adapter
performing  a  Smart  Grid
compatibility check.

(a) This LED is ONLY active for BRP069A61 (present for BRP069A62, but ALWAYS

inactive).

INFORMATION

▪

When  the  LAN  adapter  performs  a  Smart  Grid  compatibility  check,  LD4  flashes.
This is NOT erroneous behaviour. After a successful check, LD4 will either stay ON
or  go  OFF.  When  it  keeps  flashing  for  more  than  30  minutes,  the  compatibility
check failed, and NO Smart Grid operation is possible.

a
b

c

d

a

LED 1: heartbeat

b

LED 2: LAN communication

c

LED 3: P1/P2 communication

d

LED 4: smart grid control active

draft – 31/05/2022 15:53

Содержание EBLA04E V Series





































































































































































































































































































































Отзывы:

Нет отзывов