Daikin EBLA04E V Series Скачать руководство пользователя страница 49

Страница: 49 / 324

Troubleshooting

Service manual

EBLA04~08E + EDLA04~08E
Daikin Altherma 3 M
ESIE22-09 – 2022.05

Possible cause:

▪

Faulty or disturbance of the power supply (power supply MUST be within
range of nominal operating voltage ±4%),

▪

Power drop,

▪

Short circuit.

INFORMATION

If all procedures listed above have been performed and the problem is still present,
contact the helpdesk.

3.3.43 EA-00 – Outdoor unit: Cool/heat switchover problem

Trigger

Effect

Reset

Room thermistor is NOT
functioning within
operation range.

Unit will NOT stop
operating.

Automatic reset after a
continuous operation for
some time.

If the error occurs too
soon: unit will stop
operating.

Manual reset via user
interface.

To solve the error code

INFORMATION

It is recommended to perform the checks in the listed order.

Perform a check of the 4‑way valve. See

"4.2 4-way valve"

[

108].

Possible cause:

Faulty 4‑way valve.

Perform a check of the main PCB. See

"4.14 Main PCB"

[

184].

Possible cause:

Faulty main PCB.

Perform a check of the room thermistor:

▪

Measure the room temperature and compare to the room temperature
shown on the user interface (remote controller).

▪

If  temperature  shown  on  the  user  interface  differs  from  the  measured
temperature,  replace  the  user  interface  (remote  controller).  See
documentation  of  the  user  interface  (remote  controller)  for  more
information.

Possible cause:

Faulty room thermistor.

Check the communication wiring between the remote controller and the unit.
See

"4.20 User interface"

[

234].

Possible cause:

Faulty wiring between the remote controller and the unit.

Perform a check of the hydro PCB. See

"4.12 Hydro PCB"

[

175].

Possible cause:

Faulty hydro PCB.

Check that all stop valves of the refrigerant circuit are open. See

"5.2 Refrigerant circuit"

[

256].

Possible cause:

Closed stop valve in the refrigerant circuit.

Check if the refrigerant circuit is clogged. See

"5.2 Refrigerant circuit"

[

256].

Possible cause:

Clogged refrigerant circuit.

draft – 31/05/2022 15:53

Содержание EBLA04E V Series




































































































































































































































































































































Результаты поиска

Содержание EBLA04E V Series

Отзывы:

Daikin EBLA04E V Series, Руководство по обслуживанию, Страница: 49 / 324

Результаты поиска

Содержание EBLA04E V Series

Отзывы: