Daikin EBLA04E V Series Скачать руководство пользователя страница 120

Страница: 120 / 324

Components

Service manual

120

EBLA04~08E + EDLA04~08E

Daikin Altherma 3 M
ESIE22-09 – 2022.05

Are the measured voltages of the
backup heater contactor correct
(contacts closed)?

Action

Skip the next steps and continue with
the operating voltage check of the
contactor.

Deactivate backup heater: Step 1.

Measure the voltage between the following terminals of the backup heater
contactor.

▪

K1M: 1‑3
The measured voltages MUST be 0 V AC (contacts open).

Are the measured voltages of the
backup heater contactor correct
(contacts open)?

Action

Yes

heater and continue with the next
procedure.

Continue with the next step.

Measure the operating voltage on the contactor.

Result:

The measured operating voltage MUST be:

▪

230 V AC when the contacts should be closed.

▪

0 V AC when the contacts should be open.

Is the measured operating voltage of
the backup heater contactor correct?

Action

Yes

Replace the specific backup heater
contactor(s), see

Check for the reason of faulty operating
voltage (wiring, faulty contact, …), see

"7.2 Wiring diagram"

[

281].

Problem solved?

After all checking procedures listed above have been performed:

Is the problem solved?

Action

Yes

No further actions required.

Return to the troubleshooting of the
specific error and continue with the
next procedure.

Repair procedures

To remove the backup heater

Prerequisite:

Stop the unit operation via the user interface.

Prerequisite:

Turn OFF the respective circuit breaker.

Prerequisite:

Remove the required plate work, see

"4.16 Plate work"

[

202].

Drain water from the water circuit, see

"5.3.2 Repair procedures"

[

269].

Cut the tie strap(s) and remove the insulation from the backup heater.

draft – 31/05/2022 15:53

Содержание EBLA04E V Series




































































































































































































































































































































Результаты поиска

Содержание EBLA04E V Series

Отзывы:

Daikin EBLA04E V Series, Руководство по обслуживанию, Страница: 120 / 324

Результаты поиска

Содержание EBLA04E V Series

Отзывы: