Daikin EBLA04E V Series Скачать руководство пользователя страница 197

Страница: 197 / 324

Components

Service manual

197

EBLA04~08E + EDLA04~08E
Daikin Altherma 3 M
ESIE22-09 – 2022.05

Screw

Switch box

Is the problem solved?

Action

Yes

No further actions required.

Return to

"4.14.1 Checking

procedures"

[

184] of the PCB and

continue with the next procedure.

4.15 Outdoor unit fan motor

4.15.1 Checking procedures

INFORMATION

It is recommended to perform the checks in the listed order.

To perform a mechanical check of the propeller fan blade assembly

Prerequisite:

Stop the unit operation via the user interface.

Prerequisite:

Turn OFF the respective circuit breaker.

Prerequisite:

Remove the required plate work, see

"4.16 Plate work"

[

202].

If propeller fan blade touches the bell mouth, check if the fan motor is
correctly mounted on its base, see

"4.15.2 Repair procedures"

[

199].

Check the state of the propeller fan blade assembly for damage, deformations
and cracks.

Is the propeller fan blade assembly
damaged?

Action

Yes

Replace the propeller fan blade
assembly, see

Perform a mechanical check of the DC
fan motor assembly, see

"4.15.1 Checking procedures"

[

197].

draft – 31/05/2022 15:53

Содержание EBLA04E V Series




































































































































































































































































































































Результаты поиска

Содержание EBLA04E V Series

Отзывы:

Daikin EBLA04E V Series, Руководство по обслуживанию, Страница: 197 / 324

Результаты поиска

Содержание EBLA04E V Series

Отзывы: