ComAp IG-NT GC Скачать руководство пользователя

Страница: 2 / 260

IGS-NT-BC, SW Version 1.2.0,

©ComAp – January 2019

IGS-NT-BC-1.2.0 Reference Guide.PDF

Table of Contents

Table of Contents ............................................................................................................................................... 2

Document information ........................................................................................................................................ 4

Available related documentation ........................................................................................................................ 5

General guidelines .............................................................................................................................................. 6

What is described in this manual? ................................................................................................................. 6

Dangerous voltage ......................................................................................................................................... 7

Adjust set points ............................................................................................................................................. 7

Clarification of notation ................................................................................................................................... 7

Available Firmware and Archive sets ................................................................................................................. 9

Bank Controller

– firmware/hardware/archive compatibility: .......................................................................... 9

Gen-set Controller

– firmware/hardware/archive compatibility: ..................................................................... 9

General description of system with Bank Controller ........................................................................................ 10

Installation......................................................................................................................................................... 11

CAN bus wiring............................................................................................................................................. 11

Power lines wiring ........................................................................................................................................ 12

AC measurement ......................................................................................................................................... 14

BCB control and synchronizing .................................................................................................................... 16

Functions .......................................................................................................................................................... 18

OFF-MAN-AUT mode .................................................................................................................................. 18

Active and Reactive Power control in the system with Bank Controller....................................................... 19

Power management in system with Bank Controller ................................................................................... 19

Load shedding .............................................................................................................................................. 25

Circuit breakers operation sequence, CB fail detection ............................................................................... 26

Remote Alarm Messaging ............................................................................................................................ 31

Controller Redundancy ................................................................................................................................ 32

Force value

– step by step guide ................................................................................................................. 33

Values for continuous writing from external sources ................................................................................... 35

General Purpose Timers .............................................................................................................................. 35

History Related functions ............................................................................................................................. 37

User Buttons................................................................................................................................................. 38

Remote Control Function ............................................................................................................................. 39

Virtual Peripheral Inputs-Outputs (VPIO) module ........................................................................................ 39

Shared Inputs and Outputs .......................................................................................................................... 40

Distributed Binary Inputs and Outputs ......................................................................................................... 42

Modbus Reading and Writing ....................................................................................................................... 43

User MODBUS ............................................................................................................................................. 43

Modbus Switches ......................................................................................................................................... 44

Analog Input Sensors and User Sensors ..................................................................................................... 44

Languages and Translator tool in GenConfig .............................................................................................. 45

Power Formats ............................................................................................................................................. 45

System Start/Stop ........................................................................................................................................ 45

User Mask function ...................................................................................................................................... 46

PLC functions ............................................................................................................................................... 47

Multi language support ................................................................................................................................. 47

ECU interface customizing ........................................................................................................................... 47

Protections and Alarm management ................................................................................................................ 49

Configuration of User configurable protections in GenConfig ...................................................................... 54

Inputs and Outputs ........................................................................................................................................... 57

Virtual and physical modules ....................................................................................................................... 57

Setpoints ........................................................................................................................................................... 58

List of possible events ...................................................................................................................................... 59

Controller configuration and monitoring ........................................................................................................... 60

Direct connection to the PC ......................................................................................................................... 60

GenConfig functions ..................................................................................................................................... 60

InteliMonitor .................................................................................................................................................. 61

Содержание IG-NT GC





































































































































































































































































Результаты поиска

Содержание IG-NT GC

Отзывы:

Похожие инструкции для IG-NT GC

Бренды по названию

Популярные бренды

ComAp IG-NT GC, Справочное руководство

Результаты поиска

Содержание IG-NT GC

Отзывы:

Похожие инструкции для IG-NT GC

Бренды по названию

Популярные бренды