ComAp IG-NT GC Скачать руководство пользователя | Manualshive

Страница: 186 / 260

background image

IGS-NT-BC, SW Version 1.2.0,

©ComAp – January 2019

IGS-NT-BC-1.2.0 Reference Guide.PDF

186

Description

This input forces all external

remote

terminals into monitoring mode.

•

Setpoints changes are disabled.

•

Executing commands is disabled.

•

Change of controller mode is disabled.

An external remote terminal is any device, which reads and/or writes data
from/into the controller and is connected to the controller via any other
communication bus than the dedicated terminal RS485 bus.

N

OTE

:

An example of such terminal is a PC with InteliMonitor, any kind of remote display
connected via CAN2 or a PLC connected to the RS485 and communicating via
MODBUS.

Binary input: Sd override

Related FW

3.0

Description

If the input is closed, all 2nd level protections are overriden to allow engine run in
an emergency situation, e.g. when the gen-set works as a power supply for fire
extinguishing equipment.

All protections are displayed in Alarmlist and recorded into history, however the
controller leaves the gen-set in operation. If there are any protections still active or
not reset in the moment when the input is deactivated, the controller will react to
them in a standard way.

Following protections are

not

overriden by this input:

•

Emergency stop

•

Overspeed

•

Underspeed (only if

Fuel solenoid

= GAS ENGINE)

•

Binary and analog protections configured as

Sd override

type. In fact this

protection type means "Unoverridable shutdown", i.e. it works the same
way as standard shutdown protection, however it can not be overriden
(blocked) by the

input.

Binary input: BGCB disable

Related FW

3.0

Description

The input is used to disable issuing the BCB closing command.

•

If the input is active during synchronizing, the controller will keep the
genset synchronized without issuing the BCB closing command until the
input is deactivated or

is elapsed.

•

If the input is active and the BCB button is pressed in MAN mode to close
the BCB to dead bus, the BCB will not be closed until the input is
deactivated and the BCB button pressed again.

•

If the input is active and the BCB is to be closed to dead bus
automatically, the BCB will not be closed until the input is deactivated.

«
...
184
185
186
187
188
...
»

Содержание IG-NT GC





































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IG-NT GC

Бренд: XBOX Страницы: 2

Бренд: EasyIO Страницы: 12

Бренд: RMG Страницы: 6

Бренд: Data I/O Страницы: 88

Бренд: Data Aire Страницы: 13

Бренд: Hanwell Страницы: 34

Бренд: HANSONG Страницы: 11

Бренд: Datapath Страницы: 12

Бренд: Hansen Страницы: 4

Бренд: M-system Страницы: 103

Бренд: M-system Страницы: 18

Бренд: M-system Страницы: 7

Бренд: Yealink Страницы: 8

UTAdvanced UT35A

Бренд: YOKOGAWA Страницы: 18

Бренд: Heat & Cool Страницы: 5

Easywave ST01 Series

Бренд: Eldat Страницы: 2

Бренд: Valcom Страницы: 9

Бренд: Dantherm Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды