ComAp IG-NT GC Скачать руководство пользователя

Страница: 137 / 260

IGS-NT-BC, SW Version 1.2.0,

©ComAp – January 2019

IGS-NT-BC-1.2.0 Reference Guide.PDF

137

Setpoint: ExtValue4HiLim

Group

Force value

Range [units]

ExtValue4LoLim

.. 32000 [X]

Related FW

3.0

Description

This setpoint adjusts the high limit of the value of

ExtValue 4

if the value is

lowered/raised by the binary inputs

ExtValue4 up

and

ExtValue4 down

. The

ExtValue 4

is never raised over this limit.

OTE

This limit is not taken into account if the value

ExtValue 4

is written remotely from

a terminal using the appropriate command

ExtValue #n

OTE

For IS-NT only.

Setpoint: ExtValue4 rate

Group

Force value

Range [units]

1 .. 10000 [X/s]

Related FW

3.0

Force value
possible

YES

Force value
possible

YES

Description

This setpoint adjusts the rate pre second at which the

ExtValue 4

is beeing

changed while the input

ExtValue4 up

ExtValue4 down

is active.

Group: Load shedding

Setpoint: Ld shed active

Group

Load shedding

Range [units]

DISABLED, ISLAND ONLY, ISL+TRIP PARAL, ALL THE TIME [-]

Related FW

3.0

Force value
possible

YES

Description

This setpoint is used for adjustment when the load shedding function will be active
(see also IM-NT-MCB/MGCB help for more information on MCB/MGCB).

DISABLED

The Load shedding function is disabled. All the outputs
are open.

ISLAND

ONLY

In Island operation (e.g. MCB is open and MGCB is
closed) Load shedding outputs (e.g.

LdShed stage 1

)

are controlled by load shedding function.

ISL+TRIP

PARAL

This setting adjusts the same behavior as ISLAND

Содержание IG-NT GC





































































































































































































































































Результаты поиска

Содержание IG-NT GC

Отзывы:

Похожие инструкции для IG-NT GC

Бренды по названию

Популярные бренды

ComAp IG-NT GC, Справочное руководство

Результаты поиска

Содержание IG-NT GC

Отзывы:

Похожие инструкции для IG-NT GC

Бренды по названию

Популярные бренды