ComAp IG-NT GC Скачать руководство пользователя | Manualshive

Страница: 79 / 260

background image

IGS-NT-BC, SW Version 1.2.0,

©ComAp – January 2019

IGS-NT-BC-1.2.0 Reference Guide.PDF

79

Range [units]

DISABLED,ENABLED [-]

Related FW

3.0

Force value
possible

YES

Description

This setpoint can be used to aviod possible unexpected automatic start of the
gen-set in AUT mode after the gen-set was stopped by a protection and then fault
reset was pressed.

ENABLED

The controller mode is automatically changed from any mode
except OFF to MAN if any red-level protection is
acknowledged by pressing of the fault reset.

DISABLED

The automatic change of the controller mode is disabled.

N

OTE

:

The function will not work if the current controller mode is forced by one of the
inputs

Remote AUT

or

Remote TEST

.

Setpoint: Local buttons

Group

Basic settings

Range [units]

PANEL, EXTBUTTONS, BOTH [-]

Related FW

3.0

Description

The setpoint selects which set of control buttons is currently active. Its function
depends on which type of controller is used. Please refer to the section which
suits your controller/display version.

•

First section deals with the case of IGS-NT with built-in monochrome
display.

•

Second section deals with the case of IGS-NT-BB with IV5 display.

•

Third section deals with the case of IGS-NT-BB with IV8.

N

OTE

:

If you have IGS-NT (built-in display) and you use additional IV display all the
sections may be relevant (depending on the type of additional displays).

IGS-NT (built-in monochrome display)

PANEL

The built-in buttons on the controller front panel (IG-NT) or
terminal #1 (IS-NT) are enabled, the binary inputs for
external buttons are disabled.

EXTBUTTONS

The built-in buttons are disabled and the binary inputs for
external buttons are enabled.

BOTH

Both built-in buttons and binary inputs for external buttons
are enabled.

«
...
77
78
79
80
81
...
»

Содержание IG-NT GC





































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IG-NT GC

Бренд: Wasp Страницы: 16

Бренд: D-Link Страницы: 113

Бренд: D-Link Страницы: 146

Бренд: Raymarine Страницы: 12

Бренд: Jafar Страницы: 13

Бренд: Samsung Страницы: 32

Harmony Controller 2000

Бренд: A10 Страницы: 27

Бренд: Lawler Страницы: 4

Бренд: QTP Страницы: 2

Бренд: Keba Страницы: 16

Бренд: KEB Страницы: 16

Бренд: Zodiac Страницы: 12

Бренд: National Instruments Страницы: 34

Бренд: WABCO Страницы: 4

Бренд: Rayrun Страницы: 4

Бренд: Parker Страницы: 29

Бренд: ZKTeco Страницы: 43

HydroTap G5 Touch-Free Wave

Бренд: Zip Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды