ComAp IG-NT GC Скачать руководство пользователя

Страница: 93 / 260

IGS-NT-BC, SW Version 1.2.0,

©ComAp – January 2019

IGS-NT-BC-1.2.0 Reference Guide.PDF

Related FW

3.0

Description

Use this setpoint to enter the user name for the SMTP server if

SMTP

authentification

is enabled.

Setpoint: SMTP password

Group

Comms settings

Range [units]

max. 32 characters [-]

Related FW

3.0

Description

Use this setpoint to enter the password for the SMTP server if

SMTP

authentification

is enabled.

Setpoint: SMTP address

Group

Comms settings

Range [units]

max. 32 characters

Related FW

3.0

Description

AUTION

Proper setting of SMTP-related setpoints as well as controller mailbox are
essential for sending

alerts via e-mails

This setpoint is used for entering the domain name (e.g.

smtp.yourprovider.com

)

or IP address (e.g. 74.125.39.109) of the SMTP server. Please ask your internet
provider or IT manager for this information.

OTE

You may also use one of free SMTP servers, e.g.

smtp.gmail.com

. However,

please note that some free SMTP servers may cause delays (in hours..) when
sending e-mails.

OTE

If you do not want to send active e-mails, you may leave this setpoint blank, as
well as other setpoints related to SMTP server and e-mail settings.

Setpoint: Contr mailbox

Group

Comms settings

Range [units]

max. 32 characters [-]

Related FW

3.0

Description

Enter an

existing e-mail address

into this setpoint. This address will be used as

sender

address in active e-mails that will be sent from the controller.

Do not

enter your

or other recipient's e-mail address. Recipient's addresses are to be

entered into the setpoints

OTE

Most of SMTP server will reject sending e-mails that contain nonexisting address
in the sender address field.

Содержание IG-NT GC





































































































































































































































































Результаты поиска

Содержание IG-NT GC

Отзывы:

Похожие инструкции для IG-NT GC

Бренды по названию

Популярные бренды

ComAp IG-NT GC, Справочное руководство

Результаты поиска

Содержание IG-NT GC

Отзывы:

Похожие инструкции для IG-NT GC

Бренды по названию

Популярные бренды