ComAp IG-NT GC Скачать руководство пользователя | Manualshive

Страница: 85 / 260

background image

IGS-NT-BC, SW Version 1.2.0,

©ComAp – January 2019

IGS-NT-BC-1.2.0 Reference Guide.PDF

85

ECU-LINK

Connection to an electronic-controlled engine which
uses non-J1939 ECU. The proper ECU type must be
also configured with GenConfig.

Setpoint: RS232(2) mode

Group

Comms settings

Range [units]

DIRECT, MODEM (HW), MODEM (SW), MODBUS-DIRECT, MODBUS-
MDM(HW), ECU LINK [-]

Related FW

3.0

Description

This setpoint selects the connection type for the serial port COM2.

•

Available as RS232 or RS485 in the IG-NTC and IS-NT controllers.
Selectable by the setpoint

RS485(2) conv.

•

Available only as RS485 in the IG-NTC-BB and IS-NTC-BB controllers.

•

Not available in IG-NT.

See the diagram of all related terminals in the chapter

Communication

.

DIRECT

Connection to a local PC via RS232 or RS485 (with
internal or external converter) interface. Use this
option also for IG-IB connected via RS232 cable.
The internal RS485 converter is enabled/disabled by
the setpoint

RS485(2) conv.

MODEM

(HW)

Modem point-to-point connection to a remote PC
with hardware data flow control using signals
RTS/CTS. Full modem cable is required for this
option.

MODEM

(SW)

Modem point-to-point connection to a remote PC
with software data flow control. 3-wire cable (RX, TX,
GND) is sufficient for this option. Use this option only
if your modem does not provide RTS/CTS signals.

MODBUS

Modbus RTU connection in slave mode via RS232 or
RS485 (with internal or external converter) interface.
The internal RS485 converter is enabled/disabled by
the setpoint

RS485(2) conv.

, the communication

speed is adjustable by the setpoint

RS232(2)MBCSpd

. See the latest communication

guide for more information about MODBUS protocol.

MODBUS-MDM(HW)

Modbus RTU connection in slave mode via modem
with hardware data flow control. The communication
speed is adjustable by the setpoint

RS232(2)MBCSpd

. See the latest communication

guide for more information about MODBUS protocol.

ECU-LINK

Connection to an electronic-controlled engine which
uses non-J1939 ECU. The proper ECU type must be
also configured with GenConfig.

N

OTE

:

The COM2 prot is not available in the basic IG-NT version.

«
...
83
84
85
86
87
...
»

Содержание IG-NT GC





































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IG-NT GC

Бренд: Cansec Страницы: 45

Бренд: Cansec Страницы: 43

Бренд: Cansec Страницы: 32

Бренд: Lawler Страницы: 6

Бренд: Data Aire Страницы: 28

iBox Hub 25020180

Бренд: Hans Grohe Страницы: 36

Бренд: Patron Страницы: 17

Бренд: YOKOGAWA Страницы: 150

Бренд: YOODA Страницы: 3

Бренд: YMGI Страницы: 8

Бренд: POLA Страницы: 2

FAREX SR MINI SYSTEM

Бренд: RKC INSTRUMENT Страницы: 82

VARIOMATIC SARV 07.1

Бренд: AUMA Страницы: 32

Бренд: LCT Страницы: 5

Бренд: Adaptec Страницы: 2

Бренд: Webasto Страницы: 12

Airedale Sentinel

Бренд: Modine Manufacturing Страницы: 2

Бренд: Chamberlain Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды