ComAp IG-NT GC Скачать руководство пользователя | Manualshive

Страница: 87 / 260

background image

IGS-NT-BC, SW Version 1.2.0,

©ComAp – January 2019

IGS-NT-BC-1.2.0 Reference Guide.PDF

87

ENABLED

The communication port COM1 is redirected to the integrated
RS485(1) converter. The RS232(1) connector has no function
and the external display interface is not available.

DISABLED

The communication port COM1 is present at the RS232(1)
connector and the RS485(1) connector is used for the external
display interface.

N

OTE

:

The redirection is applied only for DIRECT, MODBUS and ECU-LINK modes. See
the setpoint

RS232(1) mode

N

OTE

:

This setpoint must be set to

DISABLED

at controllers that do not have internal

display. i.e. InteliVision-5 or InteliVision-8 is connected to the RS485(1) terminals.

Setpoint: RS232(2)MdmIni

Group

Comms settings

Range [units]

[-]

Related FW

3.0

Description

This setpoint can be used to add extra AT commands at the end of the
initialization sequence of the modem connected to the COM2 port. The command
can be entered with as well as without the "AT" prefix, are separated with
semicolon and maximal length is 31 characters.

The setpoint can't be modified via the IG-NT built-in terminal.

Using a modem at the COM2 port is not supported since the hardware version
2.0. For modem use the COM1 port instead.

Setpoint: RS485(2) conv.

Group

Comms settings

Range [units]

DISABLED, ENABLED [-]

Related FW

3.0

Description

This setpoint selects function of the built-in RS485(2) converter.

ENABLED

The communication port COM2 is redirected to the integrated
RS485(2) converter. The RS232(2) connector has no function.

DISABLED

The communication port COM2 is present at the RS232(2)
connector.

N

OTE

:

The redirection is applied only for DIRECT, MODBUS and ECU-LINK modes. See
the setpoint

RS232(2) mode

N

OTE

:

«
...
85
86
87
88
89
...
»

Содержание IG-NT GC





































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IG-NT GC

Бренд: VAT Страницы: 26

Бренд: Icom Страницы: 30

Бренд: ICM Controls Страницы: 2

Бренд: ICM Controls Страницы: 2

Бренд: ray Страницы: 11

Бренд: IDK Страницы: 96

Бренд: National Instruments Страницы: 2

Бренд: Rabbit Страницы: 38

Бренд: R82 Страницы: 8

Бренд: Yamaha Страницы: 92

Бренд: V2 Страницы: 12

Бренд: H3C Страницы: 5

NORA-W10 Series

Бренд: u-blox Страницы: 56

Бренд: z21 Страницы: 2

OPTISWITCH 5100 C

Бренд: KROHNE Страницы: 40

Бренд: Yoshitake Страницы: 21

Бренд: Oasis Страницы: 7

Бренд: Valcom Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды