ComAp IG-NT GC Скачать руководство пользователя | Manualshive

Страница: 88 / 260

background image

IGS-NT-BC, SW Version 1.2.0,

©ComAp – January 2019

IGS-NT-BC-1.2.0 Reference Guide.PDF

88

This setpoint has no function for IG-NT(C)-BB and IS-NTC-BB as this controller
modifications do not provide the RS232 connector at the COM2 port. The port is
redirected to the RS485 interface all the time regardless of this setpoint.

Setpoint: CAN-A bus mode

Group

Comms settings

Range [units]

32C,8C [-]

Related FW

3.0

Description

CAN bus speed selection.

•

32C: High speed CAN (250 kbps) applicable up to 32 controllers, CAN
bus length limited up to 200 meters.

•

8C: Low speed CAN (50 kbps) applicable up to 8 controllers, CAN bus
length limited up to 900 meters.

Change of this setpoint is applied after the

controller is switched off and on

again

.

N

OTE

:

Use low speed for long distance connection only. Set all connected controllers to
the same speed.

Setpoint: CAN-A emptyDet

Group

Comms settings

Range [units]

DISABLED, ENABLED [-]

Related FW

3.0

Force value
possible

YES

Force value
possible

YES

Description

Enables the detection of missing other controllers on the CAN-A bus. If the
setpoint is in ENABLED position and there aren't any other controllers detected on
the CAN-A bus (the complete bus, not only within the logical group) the alarm

CAN-A Empty

is issued.

Setpoint: CAN-B emptyDet

Group

Comms settings

Range [units]

DISABLED, ENABLED [-]

Related FW

3.0

Force value
possible

YES

Force value
possible

YES

«
...
86
87
88
89
90
...
»

Содержание IG-NT GC





































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IG-NT GC

Бренд: Samsung Страницы: 32

Бренд: Baby Jogger Страницы: 16

Бренд: YOKOGAWA Страницы: 2

ALICAT SCIENTIFIC PC

Бренд: Halma Страницы: 2

ALICAT SCIENTIFIC PCD

Бренд: Halma Страницы: 46

Бренд: WAREMA Страницы: 4

Бренд: WAGNER Страницы: 60

OPTISWITCH 5100 C

Бренд: KROHNE Страницы: 40

Бренд: Sven Страницы: 6

PersonalWorkplace Pro Video

Бренд: G&D Страницы: 56

Бренд: Beninca Страницы: 16

Бренд: Graco Страницы: 41

Бренд: Woodward Страницы: 118

Бренд: NXP Semiconductors Страницы: 39

Бренд: WEST Страницы: 2

Бренд: U-Tron Страницы: 8

Бренд: Agilent Technologies Страницы: 20

Бренд: Consort Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды