ComAp IG-NT GC Скачать руководство пользователя | Manualshive

Страница: 150 / 260

background image

IGS-NT-BC, SW Version 1.2.0,

©ComAp – January 2019

IGS-NT-BC-1.2.0 Reference Guide.PDF

150

Setpoint: Time Stamp Per

Group

Date/Time

Range [units]

1 .. 240 [min]

Related FW

3.0

Description

The setpoint adjusts the time interval for

Time stamp

records. See also the

setpoint

Time stamp act

Setpoint: #SummerTimeMod

Group

Date/Time

Range [units]

DISABLED, WINTER, SUMMER, WINTER-S, SUMMER-S [-]

Related FW

3.0

Description

The setpoint is used to select the mode of automatic daylight saving time change.

DISABLED

The automatic change to daylight saving time and back is
disabled.

WINTER

The automatic change is enabled, the current season is winter
and the controller is located in the northern hemisphere.

SUMMER

The automatic change is enabled, the current season is
summer and the controller is located in the northern
hemisphere.

WINTER-S

The automatic change is enabled, the current season is winter
and the controller is located in the southern hemisphere.

SUMMER-S

The automatic change is enabled, the current season is
summer and the controller is located in the southern
hemisphere.

Setpoint: #Time

Group

Date/Time

Range [units]

[HH:MM:SS]

Related FW

3.0

Description

The setpoint shows the current time from the internal RTC clock of the controller
and can be also used to readjust it.

N

OTE

:

If the controller is connected to other controllers via the CAN2 bus, the setpoints
#Time and #Date are automatically synchronized each hour with the controller
that has lowest address. If date/time is changed at one controller it is
automatically updated also in all other controllers in the group.

N

OTE

:

Setpoint with the symbol # are synchronized between controllers.

«
...
148
149
150
151
152
...
»

Содержание IG-NT GC





































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IG-NT GC

Бренд: Baccara Страницы: 16

Бренд: BABYSTYLE Страницы: 8

Бренд: BABYSTYLE Страницы: 32

Бренд: IDS Страницы: 2

Бренд: micro-trak Страницы: 44

Бренд: EVERSPRING Страницы: 3

Бренд: elsner elektronik Страницы: 2

Бренд: Tool-Temp Страницы: 45

769N FireLock NXT Series

Бренд: Victaulic Страницы: 40

Бренд: Flying Industry Development Страницы: 2

Бренд: Nedap Страницы: 36

MP23xxxiec Series

Бренд: YASKAWA Страницы: 102

Бренд: O&O Страницы: 64

Бренд: YASKAWA Страницы: 35

Бренд: B meters Страницы: 2

Бренд: Allen-Bradley Страницы: 162

Driver LED 1x2A/48V

Бренд: PXM Страницы: 11

Бренд: WesAudio Страницы: 65

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды