ComAp IG-NT GC Скачать руководство пользователя | Manualshive

Страница: 236 / 260

background image

IGS-NT-BC, SW Version 1.2.0,

©ComAp – January 2019

IGS-NT-BC-1.2.0 Reference Guide.PDF

236

Binary output: InMainsParal

Related FW

3.0

Description

This LBO indicates that controller (or logical group, which the controller is member
of) is connected to the mains. It means that there exists a way across MCB (IM-
NT-MCB application) or MCB+MGCB (IM-NT-MGCB application) to the controller.
It is possible to configure this signal as MCB feedback of the controller, what can
be useful for complicated applications with higher amount of mains.

N

OTE

:

This signal works correctly only if IM-NT is used as the MCB/MGCB control
device.

Binary output: Engines swapped

Related FW

3.0

Description

This output is activated by the master controller for 100 ms pulse when the priority
of two gen-sets was swapped by the

Running hours equalization

function.

Binary output: Neutral CB C/O

Related FW

3.0

Description

This output is intended for control of the neutral contactor. The output provides
continuous signal while the neutral contactor has to be closed. Use the input

NeutralCB fdb

for the neutral contactor feedback.

Response time of the contactor must be

less than 400ms

. If the contactor does

not respond to an open or close command within this time, the alarm

Wrn NCB fail

is issued.

N

OTE

:

Learn more about neutral contactor in the description of the setpoint

Binary output: PeriphCommErr

Related FW

3.0

Description

The output is closed while there is an error in the communication with any
peripheral unit (e.g. IS-AIN8, IGS-PTM, ...).

Binary output: CtrlHeartBeat

Related FW

3.0

Description

The output provides alternating signal with rate 500ms active / 500ms inactive
while the controller is

operational

, i.e. it has passed all checks after startup and

no failure was detected.

If the output does not provide the alternating signal it may indicate following:

•

controller is switched off

or

«
...
234
235
236
237
238
...
»

Содержание IG-NT GC





































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IG-NT GC

Бренд: CALEFFI Страницы: 2

Бренд: CALEFFI Страницы: 12

Бренд: Caliber Страницы: 6

Бренд: Federal Signal Corporation Страницы: 79

Бренд: Federal Signal Corporation Страницы: 32

Бренд: Hama Страницы: 7

Бренд: Hama Страницы: 44

Бренд: RadioMaster Страницы: 10

Бренд: K&K Страницы: 6

Бренд: janitza Страницы: 58

Бренд: Parkside Страницы: 86

Extra Free RZB-02

Бренд: Zamel Страницы: 2

Бренд: Yamaha Страницы: 2

Бренд: Altronix Страницы: 8

Бренд: nvent Страницы: 6

Бренд: Smart Vision Страницы: 5

Бренд: Teledyne Страницы: 47

Бренд: Western Co Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды