ComAp IG-NT GC Скачать руководство пользователя | Manualshive

Страница: 6 / 260

background image

IGS-NT-BC, SW Version 1.2.0,

©ComAp – January 2019

IGS-NT-BC-1.2.0 Reference Guide.PDF

6

General guidelines

What is described in this manual?

This manual describes „MINT“ software configuration. The software configuration is designed for multiple
sets applications with internal load sharer and synchronizer.

What is the purpose of this manual?
This manual provides general information on how to configure and operate the controller.
This manual is intended for use by:

Operators of gen-sets
Gen-set control panel builders
For everybody who is concerned with installation, operation and maintenance of the gen-set

!! Warnings !!

The NT controller can be remotely controlled. In the event that maintenance needs to be done to the gen-set,
check the following to ensure that the engine cannot be started.

To be sure:

Disconnect remote control via RS232 line
Disconnect input REMOTE START/STOP

or

Disconnect output STARTER and outputs GCB CLOSE/OPEN and MCB CLOSE/OPEN

The controller contains a large number of configurable setpoints, because of this it is impossible to describe
all of its functions. These are subject to change from SW version to SW version. This manual only describes
the product and is not guaranteed to be set for your application on arrival.

Text

ESC

(Capital letters in the frame) buttons on the front panel

Break Return

(Italic) set points

Generator protections

(Bold) Set point group

Cyan background

Valid for IS-NT only

Conformity declaration

Following described machine complies with the appropriate basic safety and health
requirement of the EC Low Voltage Directive No: 73/23 / EEC and EC
Electromagnetic Compatibility Directive 89/336 / EEC based on its design and type,
as brought into circulation by us.

Note:

ComAp believes that all information provided herein is correct and reliable and reserves the right to update
at any time. ComAp does not assume any responsibility for its use unless otherwise expressly undertaken.

«
...
4
5
6
7
8
...
»

Содержание IG-NT GC





































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IG-NT GC

Бренд: Farris Engineering Страницы: 12

Бренд: Eastern Times Technology Страницы: 4

Бренд: Vacon Страницы: 18

Бренд: Eaton Страницы: 16

Бренд: Hardi Страницы: 2

Бренд: YASKAWA Страницы: 64

Бренд: V2 Страницы: 3

Бренд: E+E Elektronik Страницы: 20

Бренд: Jands Страницы: 7

Бренд: hager Страницы: 11

coviva Smartbox TKP100A

Бренд: hager Страницы: 34

Бренд: Samson Страницы: 48

Бренд: IDTECK Страницы: 94

Ecomot300 AC2630

Бренд: IFM Electronic Страницы: 111

Бренд: Vacon Страницы: 50

Бренд: V2 Страницы: 116

Бренд: V2 Страницы: 8

Бренд: V2 Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды