Brunswick GS-X Series Скачать руководство пользователя страница 59

Страница: 59 / 302

Section Rev. February 2009

Section 1: Operations

Sweep Wagon

The sweep wagon assembly has three functions:

1. Upon ball detection or manual triggering (SET or RESET), the sweep is lowered immediately to

prevent pins from rolling forward onto the lane.

2. To guard the table as it lowers to detect or set new pins.

3. To sweep any pins that are no longer needed on the pin deck.

The sweep consists of four major components.

1. Sweep motor and drive gear

2. Sweep release assembly

3. Sweep attenuator/shock assembly

4. Sweep wagon

The sweep wagon is held up by the sweep release assembly. To lower the sweep wagon, the sweep

release assembly’s solenoid energizes to pull the swing lever rearward, allowing the tipper to rotate

to drop the sweep wagon. A sweep attenuator, along with its shock absorber, controls the drop speed.

When the sweep is fully down in the “guarding” position, switch “G” is actuated by the attenuator.

Refer to

Figures 1-24 and 1-25.

Figure 1-24. Sweep Release - Raised Position.

(1) SHOCK ABSORBER

(2) “G” SWITCH

(3) TIPPER

(4) SWEEP RELEASE LEVER

(5) SWING LEVER

(6) SWEEP RELEASE SOLENOID

(7) ATTENUATOR

Содержание GS-X Series















































































































































































































































































































Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды

Brunswick GS-X Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды