Brunswick GS-X Series Скачать руководство пользователя страница 292

Страница: 292 / 302

8-8

Section 8: Servicing

Section Rev. February 2009

2. Cut off both ends of the belt neatly and vertical to the belt axis with the belt cutter found in your

belt welding kit.

3. Pull the belt around the pulley shafts.

4. Place each belt end in the belt holder so they are slightly apart. Refer to

Figure 8-5.

(1)

BELT

HOLDER

(3)

ROUND

BELT

(2)

TIGHTEN KNURLING SCREW

AS BELT BEGINS TO MELT

Figure 8-5. Welding Round Belts.

(1) BELT HOLDER

(2) TIGHTEN KNURLING SCREW AS BELT (3)

ROUND BELT

BEGINS TO MELT

5. Push the soldering iron blade between the belt ends and bring them together heat the belt.

NOTE:

Both ends of the belt must be on the same axis on both sides of the blade.

6. When a pad of melted polycord has formed, withdraw the soldering iron, and lightly tighten the

knurling screws of the holder to bring the ends of the belt together. Refer to

Figure 8-5.

7. Tighten the knurling screws to hold the belt together. Do not overtighten.

NOTE

: DO NOT OVERTIGHTEN. The melted polycord will be pushed out and the cold

polycord left in the center will not form a weld.

8. Allow to cool for approximately two minutes before removing the belt holder .

9. Trim the bead from around the belt with a sharp knife or single edge razor blade.

10. Wait another 5-10 minutes for the belt to cool

11. Install the belt onto the pulleys.

Содержание GS-X Series















































































































































































































































































































Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды

Brunswick GS-X Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды