Brunswick GS-X Series Скачать руководство пользователя страница 289

Страница: 289 / 302

Section Rev. February 2009

Section 8: Servicing

8-5

5. Remove the top section of the spotting tong square shaft and disconnect the lower section from

the setting table.

5. Remove the top section of the stroke limiter / pin release square shaft. The lower section can

remain in place.

6. Remove the large pinholder vertical assist spring located on the front swing shaft.

7. Remove the four upper 24 mm nuts that secure the table to the deck rack tubes. Refer to

Figure 8-3.

(1)

24 mm NUTS

(2)

DECK RACK

TUBE

(3)

SETTING TABLE

STUDS

Figure 8-3. Removing Table from Deck Rack Tubes.

(1) 24 mm JAM NUTS

(2) DECK RACK TUBE

(3) SETTING TABLE STUDS

NOTE:

If the lower nuts are not moved, it makes leveling the reinstalled table quicker and

easier.

8. Manually rotate the setting table motor pulley clockwise to raise the deck rack tubes. Turning

the motor pulley clockwise will cause the sweep release assembly to lift the sweep along with

the table.

9 Rotate the pinholder to there horizontal position and allow them to lock in place..

10. Remove the setting table assembly from the pin deck area. As the back of the table approaches

the front of the machine, lift the front of the table to gain clearance under the pinsetter frame.

11. Perform the necessary maintenance or repair.

12. To reinstall, reverse the removal procedure.

13. Level the table as needed using the 24 mm nuts.

Содержание GS-X Series















































































































































































































































































































Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды

Brunswick GS-X Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды