Section Rev. February 2017
Section 5: Adjustments
5-27
TABLE HEIGHT ADJUSTMENT
i
NOTE:
Prior to making any of the following table adjustments, it is necessary that the setting
table is level with the pin deck and that switch cluster cam timing is set correctly. Refer to the
“Switch Cluster Cam Timing Adjustment”.
CAUTION: After changing the chain position on the pivot bearing or the length
of the crank arm, you must verify that the pivot bearing does not come in
contact with the main sweep arm before operating the pinsetter. Additional
clearance may be achieved by removing the pivot bearing from the crank arm
shaft, flipping it over, and reinstalling it.
The table height must be measured at two places to determine if adjustment is required. First the table
must raise to home position so that it is at it’s typical distance from the distributor and second, the
table must lowered so that the drive chain is extended fully from the crank arm.
Raised Position Measurement
With the setting table in its raised (home) position, measure the distance from top of the swing shaft
support, near the 3 pin or 6 pin, to the bottom of the distributor frame. The target distance is
140 mm
+/- 2 mm
.
Figure 5-31
.
Figure 5-31. Raised Position Measurement.
(1) DISTRIBUTOR FRAME
(2) SWING SHAFT SUPPORT
(3)
SETTING TABLE
Содержание GS-X Series
