Brunswick GS-X Series Скачать руководство пользователя страница 184

Страница: 184 / 302

5-10

Section 5: Adjustments

Section Rev. February 2017

BALL CUSHION SHOCK ABSORBER ADJUSTMENT

The shock absorber must be adjusted properly to help the ball cushion stop the ball and to prevent

damage to the shock absorber.

1. The ball cushion stop is attached to the ball accelerator housing. Pull the cushion back and

position the stop flush against the board. Refer to

Figure 5-10.

Figure 5-10. Ball Cushion Stop Bracket.

(1) CUSHION BOARD

(2) BALL CUSHION STOP BRACKET

2. Verify that lower locknut and special round nut on shock absorber bracket (

Figure 5-11)

are

installed properly. (No threads must be visible below bottom locknut.)

(2)

1 mm

GAP

(4)

LOCKNUT

(3)

SPECIAL

ROUND NUT

(1)

BRACKET

Figure 5-11. Adjust Jam Nuts on Shock Absorber Bracket.

(1) BRACKET

(2) 1 mm GAP

(3) SPECIAL ROUND NUT

(4) LOCKNUT

3. With the cushion held against the ball cushion stop, adjust the two upper jam nuts until a gap of

1 mm is obtained between the flat washer and the top of the shock absorber bracket. Refer to

Figure 5-11

. With the ball cushion being held against the ball cushion stop, the shaft must not be

bottomed in the shock absorber.

Содержание GS-X Series















































































































































































































































































































Результаты поиска

Содержание GS-X Series

Отзывы:

Brunswick GS-X Series, Руководство по эксплуатации и обслуживанию, Страница: 184 / 302

Результаты поиска

Содержание GS-X Series

Отзывы: