Brunswick GS-X Series Скачать руководство пользователя страница 80

Страница: 80 / 302

2-14

Section 2: Electronics, Switches, Solenoids and Motors

Section Rev. December 2016

TS-2 Switch

This table jam switch is mounted inside the right side frame near the switch cluster. This is a jam

switch that is activated only when the table is not able to return to its up home position. If a pin or

broken part becomes wedged between the top of the setting table and the bottom of the distributor, the

table is prohibited from rising. As the table crank continues to turn, additional torque causes the chain

sprocket and shaft to overpower a tension spring attached to the actuator lever. Any time this switch

is closed, the table motor will reverse the table for 1.5 seconds or until the “C” switch is closed. The

machine will shut off, an error code “J2” or TS2 JAM will appear on the error code display and the

status light will flash.

Turn the Stop/Run switch to the Stop position and clear the jam. Once the jam has been cleared, turn

the stop/run switch to the run position.

(1)

TS 2

TABLE JAM SWITCH

(2)

RIGHT

GUIDE TOWER

(3)

ACTUATOR

LEVER

(4)

TENSION

SPRING

(5)

SPROCKET

SHAFT

Figure 2-12. TS-2 Table Jam Switch

(1) TS2 TABLE JAM SWITCH

(2) RIGHT GUIDE TOWER

(3) ACTUATOR LEVER

(4) TENSION SPRING

(5) SPROCKET SHAFT

Error Code

TS2 Jam

JAM SWITCH TS2 (FOUND)

Содержание GS-X Series















































































































































































































































































































Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды

Brunswick GS-X Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды