Brunswick GS-X Series страница 290 Скачать руководство пользователя

Страница: 290 / 302

8-6

Section 8: Servicing

Section Rev. February 2009

CLEARING PINS JAMMED IN DISTRIBUTOR

1. Turn the stop/run on the rear mechanic’s box , Nexgen box, or mechanic’s remote display to the

stop position. If possible, turn off the main power switch on the Nexgen Controller box and

remove the incoming 3 phase power.

2. Check for pins jammed at track ejector points. Check for pins jammed at belt turning points.

Remove the jammed pins and place them on the outside return belt track.

3. Check the pin ejector assemblies for proper positions.

4. Continuous jams require checking the pin station assemblies for broken parts. Check pin

release levers.

5. Apply power to the pinsetter.

6. Check pinsetter operation.

STOPPING MACHINE IN MID-CYCLE

A machine may be stopped in mid-cycle by turning the stop/run switch on the Nexgen Controller,

mechanic’s remote display, or mechanic’s box to the stop position. Once power is restored to the

pinsetter it will automatically return to home or ready to bowl position.

If internal service work is to be performed, turn off the main power switch and if possible, disconnect

the incoming 3 phase power. Use an approved lockout device on the main power switch to prohibit the

machine from being turned on.

NOTE:

Removing the incoming 3 phase power will disable both pinsetters. Upon completion

of work, reconnect the 3 phase power, remove any installed lockout devices and turn the main

power switch on.

Once the machine has initialized, turn the stop/run switches to the run position. With older versions of

GS firmware the machine will return to the “ready to bowl” position. With newer firmware a power fail

(PF) error may be displayed. Clear the code by toggling both stop/run switches off then on.

Содержание GS-X Series















































































































































































































































































































Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды

Brunswick GS-X Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды