Brunswick GS-X Series Скачать руководство пользователя страница 64

Страница: 64 / 302

1-30

Section 1: Operations

Section Rev. February 2009

Drive Frame

The left drive frame assembly consists of the three motors along with their drive systems and the stroke

limiter assembly. See

Figure 1-29.

(1)

DISTRIBUTOR MOTOR

(1/2 HP WITHOUT BRAKE )

(3)

FRONT

DISTRIBUTOR SHAFT

(5)

SWITCH

CLUSTER HOUSING

(2)

DISTRIBUTOR MOTOR

(1/4HP WITHOUT BRAKE )

(4)

TABLE MOTOR

(1/2HP WITH BRAKE )

Figure 1-29. Drive Frame Assemblies.

(1) DISTRIBUTOR MOTOR (1/2 HP

(2) SWEEP MOTOR (1/4 HP WITH (3) FRONT DISTRIBUTOR SHAFT

WITHOUT BRAKE)

BRAKE)

(4) TABLE MOTOR (1/2 HP WITH BRAKE) (5) SWITCH CLUSTER HOUSING (6) FRONT OF MACHINE

The front motor is a 1/2 HP motor without an internal brake called the distributor motor. It uses a double

pulley system to drive the front distributor shaft and in turn the assemblies that move the pins through

the machine. This includes the distributor belts, the shark assembly, the elevator and the transport band.

The center motor is a 1/4 HP motor called the sweep motor. Its function is to drive the sweep rearward

and forward. This motor has an internal brake to prevent coasting when power is turned off thus

stopping the sweep precisely in the forward position .

The rear motor is the table motor. Its main purpose is to raise and lower the setting table. This motor is

the only one on the machine that turns both clockwise and counterclockwise. This is neccesary because

it also drives spotting tongs open and closed and it raises the sweep wagon at the end of a cycle. The 1/2

HP motor has an internal brake that locks the motor shaft when the motor is turned off. Ths primary

reason for the brake is to hold the table up is its home position. For this reason never remove the setting

table’s V-belt without first lowering the table to a safe position.

Содержание GS-X Series















































































































































































































































































































Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды

Brunswick GS-X Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды