Brunswick GS-X Series страница 169 Скачать руководство пользователя

Страница: 169 / 302

Section Rev. February 2009

Section 4: Pinsetter Cycles

4-19

Second Ball - Single Detect

Second ball - single detect is a second ball cycle used when the pinsetter is not used to provide scorer

information to an automatic scorer. This cycle would be used when automatic scorers are not present

or when an external device is used to provide pinfall to the automatic scoring system. Refer to

Figure

4-11.

(2)

PINS

(3)

(14)

SWITCH

CLUSTER

(1)

TABLE

HOME/UP

(13)

SWEEP

DOWN

(12)

SWEEP

FORWARD

(10)

GRIPPERS

OPEN

GRIPPERS

SET

NEW

PINS

(16)

SWEEP

)

RAIS

WEEP

(4)

STROKE

LIMITER

SOLENOID

ENERGIZED

(8)

NEW

PINSETTING

STROKE

(9)

OPEN 7 AND

10 PIN

GRIPPER

(5)

READY

FOR FIRST

BALL

(6)

LOAD 7

AND 10 PIN

IF AVAILABLE

(15)

DETECTION

STROKE

(17)

DETECTION

HEIGHT

Figure 4-11. Second Ball Single Detect Cycle.

(1) TABLE HOME/UP

(2) LOADING PINS

(3) CLOCKWISE

(4) STROKE LIMITER SOLENOID (5) READY FOR FIRST BALL

(6) LOAD 7 AND 10 PIN IF AVAILABLE

ENERGIZED

(7) RAISE SWEEP

(8) NEW PINSETTING STROKE

(9) OPEN 7 AND 10 PIN GRIPPER

(10) CLOSE GRIPPERS

(11) OPEN GRIPPERS SET NEW PINS (12) SWEEP FORWARD

(13) SWEEP DOWN

(14) SWITCH CLUSTER

(15) NO DETECTION STROKE

(16) SWEEP

During this cycle the table does not lower to detect the pins’ it simply sweeps away any pins left on the

pin deck and sets ten new pins in preparation for a first ball cycle.

1. The ball detect occurs.

2. In response to the ball detect signal the sweep release solenoid energizes to lower the sweep into

the guard position actuating switch “G”. The ball door solenoid energizes, locking the ball door

for three seconds.

3. The sweep motor turns on pulling the sweep back then forward to clear the pin deck. When the

sweep wagon is fully forward, switch “SM” closes and the sweep motor is turned off.

Содержание GS-X Series















































































































































































































































































































Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды

Brunswick GS-X Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды