Brunswick GS-X Series Скачать руководство пользователя страница 293

Страница: 293 / 302

Section Rev. February 2009

Section 8: Servicing

8-9

CHANGING SPOTTING TONGS

If a spotting tong becomes damaged and needs to be removed for repair, use the following procedure.

1. Turn the stop/run switch on the mechanic’s control box or mechanic’s remote display to the

stop position. (Disconnect main power to the pinsetter if you will be leaving the machine

unattended.)

2. Manually lower the setting table onto a jack stand or other suitable support.

NOTE:

If suspending the setting table on the stroke limiter plate, it must still be supported by a

jack stand or some means of support to prevent the table from dropping if the stroke limiter is

bumped or slips.

3. Turn the spotting tong square shaft until the spotting tongs are completely closed . The “ST”

switch should be open and the closed stop should be against the stop block. Refer to

Figure 8-6.

Figure 8-6. Spotting Tongs Closed.

(1) CLOSED STOP

(2) OPEN STOP

(3) GEAR RACK

(4) OPEN ST SWITCH

(5) RIGHT-HAND SQUARE SHAFT

(6) STOP BLOCK

4. Remove the hardware holding the spotting tongs to the setting table. Retain the hardware for

use during reassembly.

NOTE:

To keep the tongs timed properly, it is advisable to only remove one set of tongs at a

time.

Содержание GS-X Series















































































































































































































































































































Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды

Brunswick GS-X Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды