Brunswick GS-X Series страница 110 Скачать руководство пользователя

Страница: 110 / 302

3-18

Section 3: Nexgen Electronics

Section Rev. February 2017

MACHINE SETUP

LCD Display/User Interface

Setup and diagnostics for the both pinsetters is performed using the mechanic’s remote display. Refer to

Figure 3-10.

Figure 3-10. Nexgen Remote Display - LCD Panel

Four keys on the control panel are used to navigate the user menu.

(1) Mode Key -

Use this button to step through the pinsetter modes when the mode selection menu

is being displayed or to return to the mode selection menu.

(2) Enter Key -

The function of this key is dependent on what is being displayed on the LCD. If

the mode displayed on the LCD does not have a submenu, this key allow the user to select the

left or right lane. When the mode displayed on the LCD has a submenu, the Enter key steps

through the submenu selections.

(3) Up/Down Arrows -

The function of this key is dependent on what is displayed on the LCD.

When the mode selection menu is displayed, this key allows the user to step through the

pinsetters modes. When in a submenu, the arrow keys allow the user to toggle the choices of the

feature selected in the submenu.

Содержание GS-X Series















































































































































































































































































































Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды

Brunswick GS-X Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды