Brunswick GS-X Series Скачать руководство пользователя страница 91

Страница: 91 / 302

Section Rev. December 2016

Section 2: Electronics, Switches, Solenoids and Motors

2-25

MOTORS

All motors used on the GS-Series Pinsetters are three phase motors capable of working at 208VAC,

230VAC, or 380VAC and with either 50 or 60 hertz. For proper wiring and pulley installation

information when replacing a motor, see the “Service” section of this manual.

(1)

TABLE MOTOR

(2)

SWEEP MOTOR

(3)

ELEVATOR,

TRANSPORT BAND

AND DISTRIBUTOR

MOTOR

Figure 2-22. Pinsetter Motors

(1) TABLE MOTOR

(2) SWEEP MOTOR

(3) ELEVATOR, TRANSPORT BAND

AND DISTRIBUTOR MOTOR

(4) FRONT OF PINSETTER

Distributor Motor

The distributor motor is a 1/2 horsepower (hp) motor located at the front left corner of the pinsetter. It

drives everything that moves pins around the machine including; the round belts of the distributor, the

shovels in the elevator, and the transport band in the pit area. This motor typically runs for 45 seconds

once the pinsetter cycles. If no additional ball detect or reset occurs within that time frame, the motor

will turn off and wait until a ball is detected. If the table is waiting for pins, the motor will run up to 90

seconds. If the pins are not received by the pinholders within 90 seconds, the machine stops with a pin

load error indicating what pin(s) did not load. Refer to

Figure 2-22.

Sweep Motor

The sweep motor is a 1/4 hp motor located at the center left-hand side of the pinsetter. It drives the

sweep rearward and forward to clear pins off the pin deck. This motor has an internal brake that

prevents coasting when power is turned off to the motor. Refer to

Figure 2-22.

Содержание GS-X Series















































































































































































































































































































Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды

Brunswick GS-X Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды