Brunswick GS-X Series Скачать руководство пользователя страница 18

Страница: 18 / 302

Safety Section

Section Rev. February 2017

Pinsetter

Power-up Procedure - Safety Controller

1. Verify that the photosensors are aligned with no obstructions, the masking unit and ball

return door interlocks switches are closed and the emergency stop switch on the safety

controller in not activated (Twist the E-stop button to deactivate). Turn main power switch to

the “On”

position.

- The safety controller will start an initial power up diagnostics to verify conditions.

- The green “Restart Photosensor” LED will illuminate.

2. Press the photosensor restart button to activate the photosensor located on the masking unit.

- The green LED will go off and the yellow “Ready for Restart” LED will illuminate.

3. Press the blue “Restart” button located on the GS-X Safety Controller box to activate the

interlock switches.

- The yellow LED will go off and the red “Power On” LED will illuminate.

- Power will be supplied to the GS-X Nexgen.

VERIFY ALL INTERLOCKS

AND SENSORS ARE IN

THEIR PROPER POSITION

TURN THE MAIN POWER

SWITCH ON

(GREEN LED ON )

PRESS PHOTO SENSOR

RESTART BUTTON

(YELLOW LED ON )

PRESS RESTART BUTTON

ON CONTROLLER

(RED LED ON )

REMOVE THE SOURCE

OF THE SENSOR

OBSTRUCTION

PRESS PHOTO SENSOR

RESTART BUTTON

(YELLOW LED ON )

PRESS RESTART BUTTON

ON CONTROLLER

(RED LED ON )

VERIFY ALL INTERLOCKS

ARE IN THEIR PROPER POSITION

(YELLOW LED ON )

PRESS RESTART BUTTON

ON CONTROLLER

(RED LED ON )

Pinsetter Restart Procedure - Safety Controller

The photo sensor has been obstructed (Green, “Restart Photosensor” LED, “ON”)

1. Remove obstruction from photosensors.

2. Press the photosensor restart button to re-activate the photosensors.

3. Press the blue “Restart” button located on the GS-X Safety Controller box.

REMOVE THE SOURCE

OF THE SENSOR

OBSTRUCTION

PRESS PHOTO SENSOR

RESTART BUTTON

(YELLOW LED ON )

PRESS RESTART BUTTON

ON CONTROLLER

(RED LED ON )

The Ball Return Interlock or Masking Unit Interlock is triggered.

1. Return the masking unit and/or the ball return access door to the “closed” position.

2. Press the blue “Restart” button located on the GS-X Safety Controller box to re-activate the

interlock switches.

VERIFY ALL INTERLOCKS

ARE IN THEIR PROPER POSITION

(YELLOW LED ON )

PRESS RESTART BUTTON

ON CONTROLLER

(RED LED ON )

Содержание GS-X Series















































































































































































































































































































Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды

Brunswick GS-X Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды