Brunswick GS-X Series Скачать руководство пользователя страница 234

Страница: 234 / 302

6-10

Section 6: Troubleshooting

Section Rev. February 2009

CODE EXTENDED

CODE *

FAILURE DESCRIPTION

POSSIBLE CAUSES

G Found

SWITCH G NOT EXPECTED BUT WAS

FOUND - This error is detected when

the sweep is down when it should be

up in the raised "waiting for a ball"

position.

Replacement table motor is wired so so the table is running backwards.

Sweep release assembly defective. Check for broken parts, missing spring or

a sticky solenoid plunger.

Sweep release assembly out of alignment causing it to miss the sweep during

the clockwise rotation of the table shaft.

Sweep wagon's forward position out of adjustment. Check both sweep arms

and make sure both sweep craNK links on the sweep shaft are tight.

"G" Switch shorted. Wiring between the Nexgen Controller and the switch is

shorted.

STFound

SWITCH ST NOT EXPECTED BUT WAS

FOUND - Spotting tong switch is actuated

when it should not have been. This

means that the tongs are in thier open position

when they should have closed.

Spotting tong solenoid not energizing. Check fuses on Nexgen CPU PCB.

Spotting tong clutch slipping. Clean, reset tension and readjust.

One or more set of spotting tongs damaged or binding.

Drive gears on the square shaft or out of adjustment.

"ST" shorted or wiring on the table damaged.

OORFound SWITCH OOR NOT EXPECTED BUT

FOUND - The Out-of-Range switch,

located on the tower, is actuated when it

should not have been.

The "OOR" switch is shorted or damaged.

The wiring from the switch to the Nexgen Controller is faulty.

The Nexgen Controller CPU may be defective.

A Ntfnd

SWITCH A EXPECTED BUT NOT FOUND -

Table is not at the fully raised to

"home" position.

"A" switch is defective or out of adjustment.

Table motor or brake defective.

Check wiring connections and motor and brake connections.

Reversing fuses on Nexgen High Voltage PCB that are blown.

BNtfnd

SWITCH B EXPECTED BUT NOT FOUND -

"B" switch was not made

when table lowered to detect or set

pins.

Switch "B" defective or out of adjustment.

The wiring from the switch to the Nexgen Controller is faulty

The Nexgen Controller CPU PCB may be defective.

Reversing fuses on Nexgen High Voltage PCB that are blown

Table motor or brake is defective

Содержание GS-X Series















































































































































































































































































































Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды

Brunswick GS-X Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды