Brunswick GS-X Series Скачать руководство пользователя страница 240

Страница: 240 / 302

6-16

Section 6: Troubleshooting

Section Rev. February 2009

PROBLEM

CAUSE

CORRECTIVE ACTION

Sweep motor runs continuously.

Sweep motor brake defective.

Faulty switch SM.

All above checked. Faulty

electronic assemblies or Nexgen

CPU or H.V. PCB.

Adjust motor.

Adjust or replace switch.

Power down and exchange faulty

box. or PCBs.

Pins jammed in distributor.

Oil/grease on pins or belts.

Belts not tensioned properly,

dragging in rails.

Distributor belts off or broken.

Broken pin slider in pin station.

Front distributor and idler gears do

not have proper tooth gap or belts

are not tensioned properly.

Belts not level on distributor or

riding in top of belt rail.

Clean with all-purpose cleaner.

Remove section of belt and weld

back together, lubricate belt

Replace or weld belt.

Replace as required.

Adjust for proper tooth gap.

Replace or weld belt for proper

tension.

Adjust pulleys so the belts ride

properly in rail

10.

Shark switch not flipping to load

pins on the right pin side.

Shark solenoid.

Pin count switch not closing.

Change solenoid or make sure

solenoid is plugged in.

Check wiring to Nexgen Controller.

Adjust switch, replace or repair

switch or wirining.

11.

Incorrect score.

Pin detect switch.

Pin detection height is not correct.

Angle "1" or "2" not adjusted

Broken pin detector plate.

Switch actuator or switch is

sticking.

Adjust stroke limiter.

Adjust angle "1" or "2".

Replace pin detector plate.

Содержание GS-X Series















































































































































































































































































































Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды

Brunswick GS-X Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды