Brunswick GS-X Series страница 206 Скачать руководство пользователя

Страница: 206 / 302

5-32

Section 5: Adjustments

Section Rev. February 2017

Below are some of the possible problems that can occur if the setting table is not at the proper heights in

the Highest and Lowest positions.

Pin Deck Position

Setting Table Too

1. Setting table makes contact with lane surface.

Close To Pin Deck

2. Pins wobble when set on lane.

Setting Table Too

1. Weight of pin will not allow grippers to open to

Far From Pin Deck

release pins to the lane.

Distributor Position

Table Too Far

1. Pin grippers may not make proper contact with the

From Distributor

pin release levers to allow pins to enter the pin holder.

2. Pins may not drop into the pin holders properly, resulting in pin

jams.

Table Too Close

1. Number 3 swing shaft may make contact with right-

To Distributor

hand tower support.

2. Setting table may hit distributor.

3. Damage to the pinstation or pin slider. Pinstation release levers

fall off.

Содержание GS-X Series















































































































































































































































































































Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды

Brunswick GS-X Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды