Brunswick GS-X Series Скачать руководство пользователя страница 180

Страница: 180 / 302

5-6

Section 5: Adjustments

Section Rev. February 2017

2. Cycle the pinsetter and observe any side movement of the band on the rear roller. (Using

Diagnostics will load the band with ten pins to help in determining if the tension is proper.)

3. If the band is moving to the left, tighten the inside jam nut on the left side 1/2 turn and loosen

the inside jam nut on the right side 1/2 turn. Refer to

Figure 5-3.

If the band is moving to the

right, tighten the inside jam nut on the 1/2 turn and loosen the inside jam nut on the left 1/2

turn.

(1)

THREADED BOLT

FOR TENSIONING

(2)

BEARING JAM NUT

(3)

INSIDE JAM NUT

(4)

OUTSIDE JAM NUT

Figure 5-4. Jam Nut for Tensioning the Transport Band.

(1) THREADED BOLT FOR

(2) BEARING JAM NUT

(3)

INSIDE JAM NUT

TENSIONING

(4) OUTSIDE JAM NUT

4. After each adjustment observe the movement of the transport band. The transport band may

move sideways very slowly so allow the pinsetter to run at least 3 - 4 minutes to see any

reaction to the change in tension. Repeat step “c” as required until the band is centered and has

stopped its sideways movement.

5. Lock the outside jam nut against the inside jam nut to keep the transport band tracking properly

on the rollers.

NOTE:

Always remember to tighten the outside jam and bearing jam nuts.

Содержание GS-X Series















































































































































































































































































































Результаты поиска

Содержание GS-X Series

Отзывы:

Brunswick GS-X Series, Руководство по эксплуатации и обслуживанию, Страница: 180 / 302

Результаты поиска

Содержание GS-X Series

Отзывы: