Brunswick GS-X Series Скачать руководство пользователя страница 216

Страница: 216 / 302

5-42

Section 5: Adjustments

Section Rev. February 2017

SWEEP WAGON ROLLER ADJUSTMENT

The sweep wagon rides on guide rollers that travel in two guide rails on the pinsetter frame. The

horizontal rollers must be adjusted so the mounting bolts of the vertical rollers have a minimum

clearance of 5 mm from the inside wall of the side frame and each vertical roller is fully resting on the

rails. To adjust, loosen the mounting hardware for the horizontal guide rollers and position the sweep

side to side. Refer to

Figure 5-51.

NOTE:

Check the sweep wagon in the forward and rearward position for clearance.

Figure 5-50. Sweep Attenuator/Switch “G” Adjustment.

(1) SWITCH “G”

(2) FRONT MOUNTING PLATE (3) STOP SCREW

(4) HEX NUTS

(5) SWEEP ATTENUATOR

(6) PLUNGER FREE PLAY WITH

SWITCH

CLOSED

2. Adjust the “G” switch with the attenuator down. The switch’s plunger must have free play with

the switch closed. Refer to

Figure 5-50.

NOTE:

If free play in the plunger cannot be attained by moving the switch, increase the 85 mm

dimension 1 mm at a time until there is free play with the switch closed.

Содержание GS-X Series















































































































































































































































































































Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды

Brunswick GS-X Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды