Brunswick GS-X Series страница 224 Скачать руководство пользователя

Страница: 224 / 302

5-50

Section 5: Adjustments

Section Rev. February 2017

The “A” switch is adjusted to be contacted by the switch cam’s actuator when the table is in its highest

position. Refer to

Figure 5-62.

For further information on adjusting the “A” switch, refer to Switch

Cluster Timing adjustment in this manual.

Figure 5-62. Adjusting Switch “A.”

(1) SWITCH A IS ADJUSTED TO

CONTACT CAM WHEN SETTING

TABLE IS IN HIGHEST POSITION

Function switches, such as the Spotting Tong switch illustrated in

Figure 5-63,

are to be adjusted

as shown in View A. Views B and C illustrate being adjusted too far away and too close for proper

operation.

(1)

CORRECT

(VIEW A)

(4)

SWITCH CLOSED

WITH

PLUNGER FREE PLAY

(5)

SWITCH

OPENED

(6)

SWITCH

CLOSED

NO FREE PLAY

(2)

TOO FAR AWAY

(VIEW B)

(3)

TOO CLOSE

(VIEW C)

Figure 5-63. Spotting Tong Switches.

(1) CORRECT (VIEW A)

(2) TOO FAR AWAY (VIEW B)

(3) TOO CLOSE (VIEW C)

(4) SWITCH CLOSED WITH

(5) SWITCH OPENED

(6) SWITCH CLOSED NO FREE PLAY

PLUNGER FREE PLAY

When a switch is adjusted correctly, some free play should be available on the actuating switch plunger

when the switch is closed.

Содержание GS-X Series















































































































































































































































































































Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды

Brunswick GS-X Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды