Brunswick GS-X Series страница 127 Скачать руководство пользователя

Страница: 127 / 302

Section Rev. February 2017

Section 3: Nexgen Electronics

3-35

(8) Main Power Switch -

Controls the 3-phase power entering the box. In the off position,

this switch will disconnect power to the Nexgen box and disable both pinsetters and the ball

accelerator.

(9) 3 Phase Power In -

Input power connection for the 3-phase power. This voltage can be 208,

230 or 380 - 415 VAC.

(10) Power Out to Nexgen -

Power conection for 3 phase power to the Nexgen box.

(11) Contactors -

Power contactors used to disconnect 3 phase power whenever the emergency off

switch is pressed or an interlock switch/sensor is tripped

(12) Power Supply -

DC power supply for the photo sensor controller and the photo sensor receiver

and transmitter.

(13) Controller -

The module that monitors the photo sensor receiver and transmitter and the

interlock switches. The display on the controller provides information as to the status of the

module and the interlock switches and photo sensors. Refer to Table 6.

(14) Front Photosensor Restart -

Connection for the photosensor restart button. The button is

typically located on the back of the odd lane pinsetter, under the nexgen display, but may be

mounted at the front of the pinsetters on the making unit frame.

(15) Door Interlock -

Connection rear door interlock switches.

(16) Masking Unit Interlock -

Connection for the masking unit.

(17) Send Photo Sensor -

Connection for the safety photo sensor transmitter unit located at the front

of the pinsetters.

(18) Receive Photo Sensor

- Connection for the photosensor receiving unit located at the front of

the pinsetters.

Содержание GS-X Series















































































































































































































































































































Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды

Brunswick GS-X Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды