Brunswick GS-X Series страница 74 Скачать руководство пользователя

Страница: 74 / 302

2-8

Section 2: Electronics, Switches, Solenoids and Motors

Section Rev. December 2016

Mechanic’s Remote Display (Optional on pinsetters)

The mechanic’s remote display box is mounted the back of left lane elevator for pinsetters equipped

with the advanced guards. The box replaces the mechanic’s control box and the display of the Nexgen

electronics. The remote display box contains a display and keypad that gives the mechanic operational

control of the Nexgen electronics and shows the pinsetters’ mode and error codes. Set, reset, and stop/

run switches for both pinsetters are also provided.

Scorer < Scorer

0000000 0000000

(7)

LCD

DISPLAY

RIGHT LANE

SET

RESET

(3)

RESET

KEY

(4)

SET

KEY

MODE

ENTER

(1)

ENTER

KEY

(2)

MODE

KEY

RESET

(3)

RESET

KEY

LEFT LANE

SET

STOP

RUN

(5)

STOP/RUN

SWITCHES

(5)

STOP/RUN

SWITCHES

RUN

STOP

(6)

UP/DOWN

ARROW KEYS

(4)

SET

KEY

(1)

ENTER

KEY

(2)

MODE

KEY

STOP

RUN

STOP

(6)

UP/DOWN

ARROW KEYS

(5)

STOP/RUN

SWITCHES

(5)

STOP/RUN

SWITCHES

(3)

RESET

KEY

(4)

SET

KEY

(3)

RESET

KEY

(4)

SET

KEY

(7)

LCD

DISPLAY

Scorer < Scorer

0000000 0000000

Figure 2-6 Mechanic’s Remote Display

(1)

Enter Key -

This push button key has two functions. During pinsetter setup it is used to select

the left or right lane. Once in a configuration mode , it is used to display the different options for

the selected mode.

(2)

Mode Key -

This push button key allows the mechanic to select the pinsetter setup,

troubleshooting, or operational modes

(3) Reset Keys -

These push button keys cause the pinsetter to cycle to the next ball.

(4) Set Keys -

These push button keys causes the last combination of pins to be set.

(5) Stop/Run Switches -

This switch is used to turn the pinsetter on/off

(6) Up/Down Arrow Keys -

The function of this key is dependent on what is displayed on the

LCD. When the mode selection menu is displayed, this key allows the user to step through the

pinsetters modes. When in a submenu, the arrow keys allow the user to toggle the choices of the

feature selected in the submenu.

(7) LCD Display -

This display shows the frame count, error codes and setup information for both

pinsetters.

Содержание GS-X Series















































































































































































































































































































Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды

Brunswick GS-X Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды