Brunswick GS-X Series страница 98 Скачать руководство пользователя

Страница: 98 / 302

3-6

Section 3: Nexgen Electronics

Section Rev. February 2017

(1) P1 (Right Side Function Switches, Trouble Light and Ball Door) -

Connection for the

switches located on the right side of the odd lane (left) pinsetter. These switches include the

“A,” “B,” “C,” “D,” “SM,” “TS2,” ,“AS” (ball accelerator overload) and “OOR.” The connection

also provides the voltage for the trouble light and the ball door solenoid for the left pinsetter.

(2) P2 (Masking Unit Control) -

This connection provides power for 1st and 2nd ball lights on the

masking unit.for the odd numbered (left) lane.

(3) P3 (Rear Box Control) -

Input for stop/run switches located on the mechanic’s remote display.

(4) P4 (Ball Detect & Foul) -

This connection provides input from the ball detector, foul unit, and

ball rack reset button for the odd (left) lane

(5) P5 (Left Side Function Switches and Solenoids) -

This connection provides the input for the

“TS1,” “G,” “EC” and pin count switches. It provides voltage to the sweep release, spotting

tong, stroke limiter, and shark solenoids of the odd lane (left) pinsetter.

(6) P6 (Pin Solenoids) -

The pin holder (gripper) solenoids for the left pinsetter are energized via

the voltages sent from this connector

(7) P7 (Pin Switches) -

This connection provides input from the pin holder switches and spotting

tong (ST) switch for the left pinsetter.

(8) P8 (FX Comline In) -

This connection is used to connect to Brunswick Scoring Systems. It

provides two-way communication between the Pinsetter CPU and Brunswick Frameworx and

Vector automatic scorers If software version 4.08.03 or higher is installed, this connection is

also used to connect the pinsetter to AS-90 scorers.

(9) P9 (FX Comline Out) -

This connection is used in Frameworx Scoring Systems. It routes

communication signals through the Pinsetter CPU to the additional Frameworx lane devices

such as TV-Only monitors.

(10) P10 (Distributor Motor Power) -

Provides 3-phase power to the odd lane (left) pinsetter’s

distributor motor.

(11) P11 (Sweep Motor Power) -

Provides 3-phase power to the odd lane (left) pinsetter’s sweep

motor.

(12) P12 (Table Motor Power) -

Provides 3-phase power to the odd lane (left) pinsetter’s table

motor.

(13) P13 (Pin Light Power) -

Provides 208 or 230 VAC single phase to the odd lane (left)

pinsetter’s pin light.

(14) P14 (AC Power-In Cable) -

Input power connection for the 3-phase power coming from the

Safety Power Controller.

Содержание GS-X Series















































































































































































































































































































Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды

Brunswick GS-X Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды